Electricians in San Antonio, TX

TDLR-licensed contractors for panel work, repairs and installs — a 200-amp panel upgrade in a San Antonio home runs $1,000–$1,370 installed in the worked example below, one of the few city figures in Texas we can build from a fee schedule we could actually read line by line.

A panel with no room left for the circuit you need, a breaker that trips under ordinary loads, an outlet that has stopped working — electricians in San Antonio, TX handle that work in homes across the city. This page works a full panel example from the city's own fee schedule, explains the permit only a licensed contractor can pull here, walks through the CPS Energy release step that has no equivalent in most Texas cities, and teaches the two-part licence check. And it explains why one popular job — the EV charger install — gets unit prices here and no total.

How much does an electrician cost in San Antonio?

Start with the job this page can price locally, then the Texas ranges from the cost guide that travel with their basis labelled:

JobInstalled cost
200-amp panel upgrade or replacement, including meter loop and service work — San Antonio worked example$1,000–$1,370
Whole-home surge protector, installed at the panel (Texas range from the cost guide)$270–$320 — the device is priced at manufacturer list; see the note under the worked example
Ceiling fan replacement, on an existing fan-rated box (Texas range from the cost guide)$210–$305
GFCI receptacle replacement, one outlet on existing wiring (Texas range from the cost guide)$85–$130

The panel example is computed on San Antonio's permit schedule and San Antonio wage data — its workings are set out in full below. The three smaller rows come from the Texas electrician cost guide: each is a named part at a dated price plus a stated slice of labour built from published wage data, which is why they hold across the state. No diagnostic or service-call fee is priced anywhere on this page, because we could not verify one from primary sources. No official source publishes one, and price-setting is not part of TDLR's licensing job.

One wage figure helps you read any San Antonio quote. The U.S. Bureau of Labor Statistics puts the mean wage for electricians in the San Antonio-New Braunfels metro at $27.42 an hour (OEWS, May 2025). That is a wage, not a price: a billable rate also carries payroll taxes, insurance, vehicle, overhead and margin, which is why the example below builds its labour maths on a stated multiplier over the wage rather than pretending the wage is the rate you will be charged.

  • Free quotes
  • No obligation
  • Licensed professionals
  • Texas-focused
Electrician working at an open residential breaker panel

Electrical emergency in San Antonio: make it safe first

An electrical fault is a safety problem before it is a repair job. Work through these steps first, then call.

  • Sparks, crackling or buzzing from an outlet or switch: stop using that circuit. Switch its breaker off at the panel and leave the device alone until it has been checked.
  • A burning smell near the panel or an outlet: switch off the affected circuit — the main breaker if you cannot tell which circuit it is — and do not open the panel or investigate inside it. Call a licensed electrician.
  • The whole home has lost power: check your main breaker once. If it has not tripped and neighbouring homes are dark too, the outage is wider than your house; wait for power to return. If yours is the only dark home and the breaker looks fine, the fault may sit in your own service equipment — that is licensed work, not a DIY inspection.
  • A breaker that trips again right after a reset: do not keep resetting it. A breaker that will not stay on is reporting a fault on that circuit; leave it off and get the circuit checked.

Out-of-hours visits generally cost more than the same work booked in the working day — staffing nights and weekends costs a company more. No call-out fee or after-hours premium is printed here, because none could be verified from primary sources, so settle that charge before you agree to the visit. And nothing on this page guarantees that any particular company answers at any particular hour.

What an electrician's visit covers — and what is included

Diagnosis and repairs

A repair visit begins by isolating the fault — circuit, device and breaker tested in sequence until a failed part can be told apart from a wiring fault. The small rows above show what an honest repair price looks like: one identified part, a declared amount of labour, and the call-out fee left outside the number because no publishable basis for one exists.

Panel and service work

The panel upgrade below is the full version of this job: the old load centre out, the new one set in the same location, existing branch circuits transferred and re-terminated, the meter loop and service work the job includes, labelling, the city inspection, and the CPS Energy release that follows it. Beyond that core, quotes start to differ: extra breakers, a new meter base, mast work. The exclusions printed under the example name the lines to compare.

Small installs on existing wiring

The fan, GFCI and surge protector rows share one condition: the wiring and mounting they need already exist — a rated box waiting for the fan, a wired box for the device, a spare breaker position for the protector. Where the box or the wiring has to be created, the job changes character, and this page does not price it.

Worked example: a 200-amp panel upgrade, priced step by step

The job, with its assumptions stated: replacement of the existing panel with a 200-amp service in a single-family San Antonio home, new panel in the same location, including meter loop and service work. The permit is pulled by a TDLR-licensed electrical contractor registered with the city's Development Services Department, the city inspects the work, and a CPS Energy outage is required — the same stated spec as the cost guide's Houston example, repriced on San Antonio's schedule. The equipment is a Square D Homeline 200-amp, 40-space, 80-circuit load centre, sold as a value pack (model HOM4080M200PCVP).

LineAmountBasis
Panel (value pack)$269.00Lowe's retail price, seen November 17, 2026 — retail prices change
Permit$74.83City of San Antonio FY 2027 fee schedule: $57.50 electrical permit base fee + $3.74 service rating (0–200 amps) + $5.58 panelboard fee + $2.47 Work with CPS fee, with the schedule's 4% + 4% surcharges applied. The no-outage core is $72.17 — see the permit section
Labour$658.08–$987.128–12 hours (stated assumption: disconnect and coordinate the service changeover, remove the old panel, set the new load centre, transfer and re-terminate the existing circuits, label, attend inspection) at $82.26 an hour — see the assumption below
Total$1,000–$1,370Rounded from the two computations below

The labour line is built on a stated assumption, printed rather than buried. BLS puts the San Antonio metro's mean electrician wage at $27.42 an hour (OEWS, May 2025) — and a wage is only what the employer pays the worker. It excludes the payroll taxes, insurance, vehicle, overhead and margin the business has to recover before an hour can be sold, so we build the rate as $27.42 × 3.0 = $82.26 an hour. That multiplier is our stated assumption, not a market quote — no verified San Antonio billable rate exists, and this page never presents $82.26 as one.

A second computation, on a different wage basis, lands in the same place. Method 2 takes the Texas mean electrician wage — $28.50 an hour, a mean, read from BLS itself (OEWS, May 2025) — applies the same 3.0 assumption to reach $85.50 an hour, and produces totals of $1,027.83–$1,369.83. The two methods' midpoints sit about 3% apart, and the rounded overlap is the published $1,000–$1,370.

Per the manufacturer's datasheet for this model, the value pack bundles the 200-amp main breaker with five branch breakers. The cost box's surge protector row rests on a different kind of price: the Square D HEPD80 at its manufacturer list price of $185.00 (Schneider Electric USA, seen November 17, 2026), plus 1–1.5 hours of labour. List is a ceiling reference, not a street price — a retailer may charge less.

Not in this total: branch breakers beyond the five in the value pack (we hold no verified retail price for them), AFCI or GFCI breaker upgrades if the inspector requires them, meter base replacement, service mast or underground lateral work beyond the meter-loop scope, any CPS Energy charge (CPS invoices remodel work per project; no flat fee was verified), drywall or paint repair, and a whole-home surge protector (priced separately in the cost box).

Permits and inspections in San Antonio

San Antonio requires a permit for panel and service work, and the city is unusually direct about who may hold one. The permit is a standalone MEP Trade Permit, electrical subtype "General Electric", and Development Services states that separate trade permits "can only be obtained by licensed contractors". Only a Licensed Professional can apply for their own standalone permit, and that professional must be registered with Development Services and current on registration, insurance and state licence. A general contractor cannot pull a trade permit or request a trade inspection — the electrician on your job pulls it personally, in licence terms.

Registering the state licence with the city costs nothing. The FY 2027 fee schedule's electrical headnote states it in so many words: a state electrical licence is required to perform electrical work in San Antonio, and there is no fee to register a state licence. To register, the contractor files a photo ID, the state contractor licence card and master licence card, and proof of liability insurance.

There is no homeowner route for this permit. The city's Getting Started guidance tells homeowners they must use licensed trade contractors for electrical work — the homeowner permit it describes is a plumbing-only exception for an existing homestead residence. San Antonio states the rule affirmatively rather than leaving it to omission: panel work here goes through a licensed contractor, full stop.

The fee on this page's example is computed, not estimated, and it comes in two forms that must not be merged. The core permit is $57.50 base + $3.74 for a service rated 0–200 amps + $5.58 for the panelboard = $66.82, which with the schedule's two 4% surcharges is $72.17. Where the job needs CPS Energy to de-energise the service — a main panel and meter loop job like the example — the application selects the Work with CPS line at $2.47, and the total becomes $74.83. An interior sub-panel with no CPS outage would not select it. Publish neither figure without its condition: $72.17 core, $74.83 when a CPS outage is required.

One San Antonio shortcut does not apply here. The city's Limited Service Repair rule lets licensed contractors carry out listed minor work first and pull the permit within three working days — a new small circuit, ceiling fans onto approved boxes, bonding work. It expressly does not reach work like a service or panel upgrade, so this job follows the regular route: permit first, inspection, then release.

San Antonio works to the 2023 National Electrical Code with local amendments, in force in the city from May 1, 2025.

CPS Energy: the release step after inspection

A San Antonio panel job has a second gate after the city's, and it belongs to CPS Energy, the city's utility. The mechanism is built into the permit itself. When the Work with CPS fee is paid at application and the work type is set to Residential, the job enters what Development Services calls a Systematic Release: once your inspections are approved, the city notifies CPS Energy that the property is safe to turn on, and CPS releases the work request to scheduling. Permanent-power release is completed manually once inspections have passed or been conditionally approved and any outstanding fees are paid.

From the customer's side, a remodel or service job starts with a CPS service request — CPS assigns a designer to the work request, and any CPS charges are invoiced for your project rather than read off a flat published fee; none was verified for this page, so none is printed. The sequence to hold your contractor to is the one both organisations publish: permit, work, city inspection passed, then utility release. An electrician who offers to skip the middle steps is offering to leave your service outside the system that reconnects it.

Choosing electricians in San Antonio, TX: the two-part licence check

San Antonio adds a city registration on top of the state licence, but the licence itself is Texas's, issued by TDLR and valid statewide. Verifying it means running two lookups, not one — the company's record names its master but stays silent about whether that master's own licence is in force:

  1. 1

    Start with the licence number, wherever the company prints it — truck, quote, invoice. It appears there with the TECL prefix; TDLR License Search wants the number without it.

  2. 2

    Find the company's own record, headed Electrical Contractor (Type: EC). Confirm the business name, address and county are the firm you are dealing with, the status reads Active, and the expiration date is still in the future.

  3. 3

    Look for the "Master:" line on that record: it gives the Master Electrician of Record by name, with his licence number and expiration.

  4. 4

    Take that name or number and search a second time, for the Master Electrician (Type: ME) record. It has to be the same person, same number — and this record, unlike the first, shows his own status, which must also be Active and unexpired.

  5. 5

    A lapse at either stage — an expired record, a master who cannot be found, details that do not correspond — means the company is not currently in order to hire, whatever the truck says.

  6. 6

    Optionally, run the name through TDLR's final-orders search as well: it lists fines, suspensions and revocations.

Two structural rules explain why the check is built this way. A contractor must be a master, or employ one as its master of record — and a master may be assigned to just one contractor at a time unless he owns more than half of that business. And the contractor must keep commercial general liability cover of at least $300,000 per occurrence, $600,000 aggregate and $300,000 for products and completed operations in force at all times. Then add the city question: is this contractor registered with Development Services? An unregistered contractor cannot pull your permit. Ask for the insurance certificate, get the quote in writing with its exclusions named, and keep the final payment until the inspection passes and CPS has released the service.

EV chargers in San Antonio: what we can price, and what we cannot

Pricing the charger is the easy part: two named units, seen November 17, 2026 — the ChargePoint Home Flex Level 2 charger at $599.00 (Home Depot) and the Tesla Wall Connector at $635.00 (Tesla's own store).

Pricing the installation is where honesty runs out, so this page prints no installed total, because we could not verify one from primary sources. What decides the figure is the circuit run from panel to charger, and no two San Antonio homes present the same run: a panel on the garage wall is one job, a panel across the house is another. The cable and the two-pole breaker that run needs carry no verified retail price in our research, and a panel without spare capacity turns the charger job into the panel upgrade above as well. Instead of a range, put three questions to any quoting company: what run length does the quote assume, are the breaker and permit inside it, and was your panel's capacity actually checked?

What changes the cost in San Antonio

Whether a CPS outage is part of the job

The worked example includes meter loop and service work requiring CPS Energy to de-energise, which is why its permit is $74.83. A panel job with no utility outage carries the $72.17 core permit instead. The difference is small money, but it is the first scope line to compare when two quotes for "a panel job" describe the same work differently.

Breakers beyond the box

Five branch breakers come in the box with the main breaker. Beyond those, every additional breaker is an added part — and an inspector applying the 2023 NEC can require AFCI or GFCI breaker upgrades on top. No retailer price for them could be verified for this page, so look for them as an itemised line on a real quote, and ask for it if it is missing.

Panel location and access

The example assumes the new panel goes where the old one stood, on circuits of workable length. Relocate the panel, or find service equipment that needs mast or meter base work once opened up, and the job leaves the example's scope — and its total — behind.

Timing: nights, weekends and peak season

Everything priced here assumes ordinary working hours. Fault-finding at night or on a weekend generally costs more; each company sets that premium itself, and no published rate exists for us to verify. Have the call-out basis stated before the visit, not after it.

San Antonio electrician questions

How much does a 200-amp panel upgrade cost in San Antonio?

$1,000–$1,370 installed in our worked example: a Square D Homeline value pack at $269.00 retail, the city's permit at $74.83 with the CPS outage line selected, and 8–12 hours of labour built from BLS wage data under a stated 3.0-times assumption, cross-checked on a second wage basis. Excluded lines — extra breakers, meter base work, any CPS project charges — are printed with the example, and a quote that includes them will run higher.

How much is the electrical permit for a panel upgrade in San Antonio?

$72.17 at its core — a $57.50 base fee, $3.74 for a service rated 0–200 amps and $5.58 for the panelboard, plus the schedule's 4% + 4% surcharges. When the job requires a CPS Energy outage, as a main panel and meter loop job does, the Work with CPS line adds $2.47 before surcharges and the total is $74.83. Both figures come from the city's FY 2027 fee schedule.

Can I pull my own electrical permit in San Antonio?

No. Development Services states that homeowners must use licensed trade contractors for electrical work; the homeowner permit the city describes covers plumbing on an existing homestead residence, not electrical work. A panel permit here is pulled by a Licensed Professional registered with the city.

Who pulls the permit for a panel job in San Antonio?

The licensed electrical contractor, registered with Development Services — not your general contractor, who cannot pull a trade permit or request a trade inspection. Registering a state licence with the city carries no fee, and the contractor must be current on registration, insurance and licence before the permit issues.

What is the Work with CPS step?

It is San Antonio's way of joining the permit to the utility. The fee is selected on the permit application when the job needs CPS Energy to de-energise the service. Once the city's inspections are approved, Development Services notifies CPS that the property is safe to turn on and the work request is released to scheduling. It is the step that gets your power restored through the system rather than around it.

How do I check an electrician's licence in San Antonio?

On TDLR License Search, in two lookups. First the company's Electrical Contractor record (Type: EC): it should read Active and unexpired, and its "Master:" line names the Master Electrician of Record. Then that master's own Master Electrician record (Type: ME): the name and number must match the contractor record, and his status must be Active as well. San Antonio's separate requirement is city registration, which the permit itself proves: an unregistered contractor cannot pull one.

How much does it cost to install an EV charger in San Antonio?

We publish the units we can verify and stop there. The units: a ChargePoint Home Flex at $599.00, a Tesla Wall Connector at $635.00. The installed figure depends on the cable run from your panel to the charger — different in every home — and we hold no verified prices for the cable or breaker, so any single range we printed would be invented.

Do San Antonio electricians charge a service-call or diagnostic fee?

Many do — but you will not find the figure here, because no official source publishes a San Antonio diagnostic fee and TDLR's licensing does not extend to regulating charges. Before booking, ask what the visit costs and whether the fee comes off the repair bill if you go ahead — and get both answers before anyone is dispatched.

Areas served in and around San Antonio

Tell us your neighbourhood when you request a quote, and we will match you with a professional who covers your part of the city.

When it lands, the list will describe the area this page serves for matching homeowners with professionals. It is this page's coverage statement — it says nothing about where any individual company will or will not travel.

Related services and other Texas cities

Disclaimer. The costs on this page are estimates only, computed from the sources below with their assumptions printed next to them. Your final price depends on your home, the job and the scope you agree, and costs vary by job, material and location. Always confirm a contractor's licence and insurance before work starts.

Sources

  • Texas Department of Licensing and Regulation — electrician licensing: contractor licence, Master Electrician of Record, insurance minimums, License Search and final-orders search (tdlr.texas.gov)
  • Texas Legislature — Occupations Code Chapter 1305, including §1305.151, §1305.201 and §1305.003(a)(6)
  • City of San Antonio, Development Services — MEP Trade Permit ("General Electric") guidance and Getting Started page; FY 2027 Development Fee Schedule, electrical section; Information Bulletin 250 (Work with CPS) and CPS Release Requirements — Residential (sa.gov / docsonline.sanantonio.gov)
  • CPS Energy — Residential Electric and Gas Remodel Process; Electric Service Standards (cpsenergy.com)
  • U.S. Bureau of Labor Statistics, OEWS May 2025 — electrician wages: San Antonio metro mean and Texas mean, both read from BLS (bls.gov)
  • Lowe's — Square D Homeline 200-amp load centre value pack, $269.00; Hunter Toledo 52-in ceiling fan, $126.00; Square D X Series GFCI receptacle, $41.84 — retail prices seen November 17, 2026
  • Schneider Electric USA — Square D HEPD80 surge protective device, manufacturer list price $185.00, seen November 17, 2026
  • The Home Depot — ChargePoint Home Flex Level 2 EV charger, $599.00, seen November 17, 2026; Tesla Shop — Wall Connector, $635.00, seen November 17, 2026
Call for a free quote Get a Quote