Electricians in Dallas, TX

TDLR-licensed contractors for panel work, repairs and installs — and a gate most pages never mention: on top of the Texas licence, the electrician who pulls your Dallas permit must be a Master Electrician registered with the city in its DallasNow system, because a journeyman cannot pull one at all.

A panel stuffed full when you need one more circuit, a breaker that trips under an ordinary load, a dead outlet in a room that matters — electricians in Dallas, TX cover that work in homes across the city. What this page will not do is print a Dallas panel example: the city's own documents price the permit's inspection component two different ways and never say whether it stacks, so a Dallas total built on it would be invented. What it does instead is show you the fully worked Texas benchmark with its basis labelled, the permit and registration rules that are verified — including the one fee the city does state plainly and the one it contradicts itself on — and the licence check that takes five minutes.

How much does an electrician cost in Dallas?

Dallas electricians charge by the job. The ranges this page can stand behind are the Texas ranges from the electrician cost guide, each printed with the basis it stands on:

Job (Texas ranges from the cost guide)Range
200-amp panel upgrade or replacement, including meter loop and service work — guide's worked example, computed on Houston's permit schedule$1,090–$1,470
Whole-home surge protector, installed at the panel$270–$320 — plus the note below: the device is priced at manufacturer list
Ceiling fan replacement, on an existing fan-rated box$210–$305
GFCI receptacle replacement, one outlet on existing wiring$85–$130

Read the labels before you budget. The panel benchmark is a Texas worked example with Houston's permit inside it, because Houston's fee schedule could be verified line by line and Dallas's total could not — the permit section below shows exactly where the city's documents disagree with each other. Your Dallas permit charges will be different numbers, set out on the permit paperwork your contractor receives. The three smaller rows travel because of how they are built: an identified part at a dated retail price, plus labour hours costed from published wage data. One label matters in that table — the surge protector's device is in at the manufacturer's list price of $185.00, and list prices sit at or above street prices. One figure is missing on purpose: a diagnostic or service-call fee, because we could not verify one from primary sources. No official source publishes one, and TDLR does not regulate prices.

One wage figure helps you read any Dallas quote: BLS puts the mean hourly wage for electricians across the Dallas-Fort Worth-Arlington metro — published as one combined metro, not two cities — at $28.83 (OEWS, May 2025). It is a wage, not a price: the rate on your quote must also recover payroll taxes, insurance, vehicle, overhead and margin, which is why the guide builds its labour maths on a stated multiplier over the wage rather than pretending the wage is the rate you will be charged.

  • Free quotes
  • No obligation
  • Licensed professionals
  • Texas-focused
Electrician working at an open residential breaker panel

Electrical emergency in Dallas: make it safe first

An electrical fault is a safety problem before it is a repair job. Work through these steps first, then call.

  • Sparks, crackling or buzzing from an outlet or switch: stop using that circuit. Switch its breaker off at the panel and leave the device alone until it has been checked.
  • A burning smell near the panel or an outlet: switch off the affected circuit — the main breaker if you cannot tell which circuit it is — and do not open the panel or investigate inside it. Call a licensed electrician.
  • The whole home has lost power: check your main breaker once. If it has not tripped and neighbouring homes are dark too, the outage is wider than your house; wait for power to return. If yours is the only dark home and the breaker looks fine, the fault may sit in your own service equipment — that is licensed work, not a DIY inspection.
  • A breaker that trips again right after a reset: do not keep resetting it. A breaker that will not stay on is reporting a fault on that circuit; leave it off and get the circuit checked.

Expect an out-of-hours visit to cost more than the same job in the working day — unsocial hours cost a company more to staff. No call-out fee or after-hours premium is published here, because none could be verified from primary sources, so ask for the call-out charge before you agree to the visit. Nothing on this page promises that a given company will answer at a given hour.

What an electrician's visit covers — and what is included

Diagnosis and repairs

Diagnosis comes first on a repair visit: the circuit, the device and the breaker are tested in sequence, so a failed part is separated from a wiring problem before money is spent on either. The small rows in the cost box show the honest shape of that bill — one named part, a stated slice of labour, and any call-out fee sitting outside the figure because no publishable basis for one exists.

Panel and service work

A panel upgrade is the full version of the job: old load centre out, new one set in its place, branch circuits transferred and re-terminated, the meter loop and service work the job includes, labelling, and the city inspection. In Dallas it also means the stand-alone permit described below, pulled by a registered master, and a reconnection only Oncor may make. Past that scope, quotes diverge — extra breakers, a new meter base, mast work — so ask for those lines to be itemised.

Small installs on existing wiring

The fan, GFCI and surge protector rows share an assumption: the mounting and wiring already exist — a fan-rated box, a wired device box, a spare breaker position in the panel. A fitting that needs the wiring or the box created first is different work, and it is not priced on this page.

Permits and contractor registration in Dallas

Dallas requires a permit for this work. The city's Trade Permit Guide puts it plainly: an electrical permit is required for any wiring, panel upgrades, new circuits, service changes, or electrical work on a building. For a panel job the permit is a stand-alone one — the city's Service First Bulletin #204 requires a separate Residential Electrical Permit for "panelboard additions, replacements, or relocations" and for "service rebuilds, including transfer switches or relays", rather than folding the work into another permit.

Who pulls it is narrower than most cities. The city's guide states it directly: a registered Master Electrician can pull the permit — journeyman electricians cannot pull permits independently and must work under a licensed master — and the master must be registered in DallasNow, the city's permitting system. Registration is done in person before the Chief Electrical Code Administrator; it requires an established place of business and general liability insurance of not less than $300,000 combined single limit per occurrence, and the city's registration packet warns that the system will not issue a permit to a contractor who is not registered, whose registration has expired, or whose insurance has lapsed. The city's stated registration fee is $160 for two years, and permitting privileges stop at expiry until it is renewed. Dallas also requires a qualified electrician of the proper classification to be present on site, in direct supervision, while permit-required work is done.

About the permit fee, this page prints the part the city verifies and names the part it contradicts. The stand-alone electrical permit itself is stated by the city, in Service First Bulletin #204, as $196 — a $181 permit fee plus a $15 technology fee. What the city's documents do not settle is the trade inspection fee charged alongside it: the same bulletin lists $100, while the city's ordinance and its Planning & Development Guide both state $125 for one trade — and no document we opened says whether that inspection fee is charged on top of the $196 for an ordinary panel permit at all. Until the city reconciles its own figures, a single Dallas permit total from us would be a guess, so we print $196 as what it is — the permit and technology fee — and tell you the inspection fee is additional and disputed between the city's own publications. Ask your contractor to show you the fee lines on the permit paperwork; that document, not any website, is the record of what the city charged.

The homeowner route exists in Dallas — behind an exam. City code (Chapter 56, §81.3) lets a homeowner personally install electrical work on homestead premises they own and occupy, but only after filing approved plans and satisfying the chief electrical code administrator of their ability by passing an approved written or oral examination, then securing the permit and paying the fees. The same section bars the homeowner from hiring anyone to assist in any way on permit-required work. So the Dallas DIY route is real but narrow: pass the city's exam, do every part of the work yourself, or hire a licensed, registered master. It is a genuine contrast with Houston, where no homeowner electrical permit exists at all.

Oncor makes the connection — nobody else. Under Chapter 56, §81.1, only authorised employees of Oncor Electric Delivery may connect Oncor's service conductors to your service entrance conductors, and meter disconnection, connection and reconnection are Oncor-only as well. The sequence for a planned panel job runs: your electrician installs or rebuilds the meter base and service equipment, the city inspects, the city sends Oncor its confirmation, and Oncor installs the meter or reconnects. A city policy that releases power before inspection exists for storm, fire and vehicle damage at an inspector's discretion — it is an emergency policy, not the planned-upgrade process, and this page does not present it as one.

Dallas works to the 2023 National Electrical Code, adopted by the city's amending ordinance effective May 23, 2025.

Choosing electricians in Dallas, TX: the licence, then the registration

Dallas runs two gates, and a company has to pass both before it can legally do your panel job. The first is the Texas licence, and checking it is itself a two-part job — because the record that names a company's master never prints that master's own status:

  1. 1

    Ask the company for its licence number. On trucks and paperwork it carries the TECL prefix; in TDLR License Search you enter the number without it.

  2. 2

    Pull up the company's record — the title to look for is Electrical Contractor (Type: EC). The name, address and county should be the business in front of you, the status Active, the expiration date still ahead.

  3. 3

    Find the "Master:" line on that record. It names the Master Electrician of Record and gives his licence number and expiration.

  4. 4

    Now search that master separately — by his name, or by the number you just copied — and open the Master Electrician (Type: ME) record. The name and number must match what the contractor record showed, and this record must also read Active and unexpired.

  5. 5

    A failure at either step — an expired record, a master who cannot be found, names that do not line up — means the company is not currently in order to hire, whatever the truck says.

  6. 6

    For the fuller picture, TDLR's final-orders search shows enforcement actions taken against licensees.

Two facts sit underneath the search. A contractor must be, or employ, its master of record — and a master may serve only one contractor at a time unless he owns more than half of that business. And the contractor must carry commercial general liability insurance of at least $300,000 per occurrence, $600,000 aggregate and $300,000 for products and completed operations, maintained at all times.

The second gate is Dallas's own. Run the same company through the registration question: is the master who will pull your permit registered with the city in DallasNow, for the electrical trade? The city's own guide teaches this check to consumers, with a sharp edge: if a contractor pulls a permit while not registered for that trade, the permit can be voided. Ask for the insurance certificate, get the quote in writing with its exclusions named, and keep the final payment until the inspection passes.

EV chargers in Dallas: what we can price, and what we cannot

The charger itself is the easy part to price: two named units, seen November 17, 2026 — the ChargePoint Home Flex Level 2 charger at $599.00 (Home Depot), the Tesla Wall Connector at $635.00 (Tesla's own store).

The installed total is where this page stops, because we could not verify one from primary sources. What drives it is the circuit run from your panel to the charger, and that length is set by your home: a panel on the garage wall and a panel across the house are different jobs. We hold no verified retail price for the cable or the two-pole breaker the circuit needs, and if your panel has no spare capacity, a panel upgrade becomes part of the job. Instead of inventing a range, put three questions to any quoting company: what run length the quote assumes, whether the breaker and permit are in it, and whether your panel's capacity was actually checked.

What changes the cost in Dallas

Whether service work is part of the job

The benchmark example includes the meter loop and service work; a panel swap without service work is a smaller job with fewer hours. If two quotes for "a panel job" disagree, compare this line first — the scopes may not match.

Breakers beyond the box

In the guide's example the panel arrives as a value pack: main breaker and five branch breakers included. Circuits beyond five need more breakers, and the inspector may require AFCI or GFCI upgrades under the 2023 NEC besides. Those parts could not be priced from a retailer for this page — expect a separate line on a real quote, and ask for it to be itemised.

Panel location and access

The benchmark leaves the panel where it stands, on existing circuits of workable length. A moved panel — or service equipment that turns out to need mast or meter base work — sits outside the benchmark's scope and its total.

Timing: nights, weekends and peak season

Planned work is priced from ordinary hours; the same fault-finding at night or on a weekend usually costs more. Each company sets that premium, and no published rate exists that we can verify. Agree the call-out basis before the visit, not after it.

Dallas electrician questions

How much does a 200-amp panel upgrade cost in Dallas?

This page publishes no Dallas total, deliberately. The fully worked Texas example in the cost guide — a Square D Homeline value pack at $269.00 retail, a city permit, and 8–12 hours of labour built from BLS wage data under a stated 3.0-times assumption — comes to $1,090–$1,470, but the permit inside that figure is Houston's, and Dallas's permit total is one we could not verify (see the next answer). Use the benchmark to judge the shape of a Dallas quote, not as the quote.

How much is the electrical permit for a panel upgrade in Dallas?

Partly stated, partly unsettled — and the unsettled part is the city's, not ours. Service First Bulletin #204 prices the stand-alone electrical permit itself at $196: a $181 permit fee plus a $15 technology fee. A trade inspection fee applies alongside permits, but the bulletin lists it at $100 while the city's ordinance and Planning & Development Guide state $125 for one trade, and no city document we opened says whether it is charged on top of the $196 for this permit. We print the $196 and the conflict, not a total. Your contractor's permit paperwork shows what the city actually charged.

Do I need a permit to replace my electrical panel in Dallas?

Yes. Panelboard replacements and service rebuilds require a separate stand-alone Residential Electrical Permit under Service First Bulletin #204, and the work is inspected. Skipping it is a code violation, and a permit pulled by a contractor who is not registered for the trade can be voided.

Can I pull my own electrical permit in Dallas?

Only through the city's exam route. Chapter 56, §81.3 lets a homeowner work on homestead premises they own and occupy after filing approved plans and passing an approved written or oral examination set by the chief electrical code administrator — and the homeowner may not hire anyone to assist in any way. If you want help on the job, the help has to be a licensed, registered master electrician pulling the permit.

Who can pull an electrical permit in Dallas?

A registered Master Electrician, registered with the city in DallasNow. Journeyman electricians cannot pull permits independently — they work under a licensed master. The city's system will not issue a permit to a contractor whose registration or insurance has expired.

How do I check an electrician's licence in Dallas?

In two parts, on TDLR License Search. First the company's Electrical Contractor record (Type: EC) — Active, unexpired — whose "Master:" line names the Master Electrician of Record. Then the master's own Master Electrician record (Type: ME): name and number matching, status Active. Then ask the Dallas question on top: is the master registered in DallasNow for the electrical trade? Both gates have to pass.

How much does it cost to install an EV charger in Dallas?

In parts, because only the parts verify. The units: $599.00 for a ChargePoint Home Flex, $635.00 for a Tesla Wall Connector. The installed figure turns on the cable run from your panel to the charger — different in every home — and we hold no verified prices for the cable or breaker, so any single range we printed would be invented.

Do Dallas electricians charge a service-call or diagnostic fee?

Many do; the figure does not appear here. No official source publishes a Dallas diagnostic fee, and TDLR licenses electricians without regulating their charges. Ask two questions before booking — what the visit costs, and whether the fee is credited toward the repair if you proceed — and get both answers before anyone is dispatched.

Areas served in and around Dallas

Tell us your neighbourhood when you request a quote, and we will match you with a professional who covers your part of the city.

When it lands, the list will describe the area this page serves for matching homeowners with professionals. It is this page's coverage statement — it says nothing about where any individual company will or will not travel. Dallas and Fort Worth share a metro but not a permitting office: if your home sits on the other side of the line, see electricians in Fort Worth, TX.

Related services and other Texas cities

Disclaimer. The costs on this page are estimates only, computed from the sources below with their assumptions printed next to them. Your final price depends on your home, the job and the scope you agree, and costs vary by job, material and location. Always confirm a contractor's licence and insurance before work starts.

Sources

  • Texas Department of Licensing and Regulation — electrician licensing: contractor licence, Master Electrician of Record, insurance minimums, License Search and final-orders search (tdlr.texas.gov)
  • Texas Legislature — Occupations Code Chapter 1305, including §1305.151, §1305.201 and §1305.003(a)(6)
  • City of Dallas — Planning & Development Guide, Trade Permit Guide (Electrical); Service First Bulletin #204; Dallas City Code Chapter 56 (§§81.1, 81.2, 81.3, 82.8) and Chapter 52; Electrical Contractor Registration packet (dallascityhall.com / dallas.gov)
  • Oncor Electric Delivery — service connection and meter guidance (oncor.com)
  • U.S. Bureau of Labor Statistics, OEWS May 2025 — electrician wages: Dallas-Fort Worth-Arlington metro mean and Texas mean, both read from BLS (bls.gov)
  • Lowe's — Square D Homeline 200-amp load centre value pack, $269.00; Hunter Toledo 52-in ceiling fan, $126.00; Square D X Series GFCI receptacle, $41.84 — retail prices seen November 17, 2026
  • Schneider Electric USA — Square D HEPD80 surge protective device, manufacturer list price $185.00, seen November 17, 2026
  • The Home Depot — ChargePoint Home Flex Level 2 EV charger, $599.00, seen November 17, 2026; Tesla Shop — Wall Connector, $635.00, seen November 17, 2026
Call for a free quote Get a Quote