Electricians in Austin, TX

TDLR-licensed contractors for panel work, repairs and installs — and a second desk most Texas cities do not have: in Austin a panel upgrade needs the city's permit and Austin Energy's service approval, in that order, before anyone de-energises your home.

A panel with no capacity left for the charger or the addition you are planning, a breaker that trips under an ordinary load, a dead outlet in a room that matters — electricians in Austin, TX cover that work in homes across the city. What this page will not do is print an Austin permit fee: no line in the city's residential fee schedule prices the stand-alone permit this job uses, and the schedule itself could not be read first-hand, so a figure would be borrowed, not verified. What it does instead is show you the fully worked Texas benchmark with its basis labelled, the two-approval sequence Austin actually runs — permit, utility outage, inspection, re-energise — and the licence check that takes five minutes.

How much does an electrician cost in Austin?

Austin electricians price by the job, not by the visit. Below are the Texas ranges from the electrician cost guide — the ones this page can stand behind — each printed with the basis it stands on:

Job (Texas ranges from the cost guide)Range
200-amp panel upgrade or replacement, including meter loop and service work — guide's worked example, computed on Houston's permit schedule$1,090–$1,470
Whole-home surge protector, installed at the panel$270–$320 — plus the note below: the device is priced at manufacturer list
Ceiling fan replacement, on an existing fan-rated box$210–$305
GFCI receptacle replacement, one outlet on existing wiring$85–$130

Read the labels before you budget. The panel benchmark is a Texas worked example with Houston's permit inside it, because Houston's fee schedule could be verified line by line and Austin's permit has no priceable line at all — the permit section below explains the gap plainly rather than papering over it. Your Austin permit and Austin Energy charges will be different numbers, set by the city and the utility for your job. The three smaller rows are priced the way the guide prices everything: a named part at a dated retail price, plus labour hours costed from published wage data under a declared assumption — a method that holds anywhere in Texas. One caution rides with the surge protector: its device enters at the manufacturer's list price of $185.00, and list is not what retailers necessarily charge. A diagnostic or service-call fee, by contrast, gets no number at all, because no official source publishes one and TDLR does not regulate prices.

One wage figure helps you read any Austin quote: the BLS mean for electricians in the Austin-Round Rock-San Marcos metro is $29.25 an hour (OEWS, May 2025). Read it as a wage and nothing more — the billable rate a company charges has to recover payroll taxes, insurance, vehicle, overhead and margin on top of it, which is why the guide builds its labour maths on a stated multiplier over the wage rather than pretending the wage is the rate you will be charged.

  • Free quotes
  • No obligation
  • Licensed professionals
  • Texas-focused
Electrician working at an open residential breaker panel

Electrical emergency in Austin: make it safe first

An electrical fault is a safety problem before it is a repair job. Work through these steps first, then call.

  • Sparks, crackling or buzzing from an outlet or switch: stop using that circuit. Switch its breaker off at the panel and leave the device alone until it has been checked.
  • A burning smell near the panel or an outlet: switch off the affected circuit — the main breaker if you cannot tell which circuit it is — and do not open the panel or investigate inside it. Call a licensed electrician.
  • The whole home has lost power: check your main breaker once. If it has not tripped and neighbouring homes are dark too, the outage is wider than your house; wait for power to return. If yours is the only dark home and the breaker looks fine, the fault may sit in your own service equipment — that is licensed work, not a DIY inspection.
  • A breaker that trips again right after a reset: do not keep resetting it. A breaker that will not stay on is reporting a fault on that circuit; leave it off and get the circuit checked.

Night and weekend call-outs usually cost more than the same job in normal hours, because unsocial hours cost a company more to staff. This page publishes no call-out fee and no after-hours premium, because none could be verified from primary sources, so get the call-out charge agreed before the visit. It also promises nothing about any particular company's hours.

What an electrician's visit covers — and what is included

Diagnosis and repairs

A repair visit is a search before it is a fix: the circuit, the device and the breaker are tested in an order that separates a failed component from a fault in the wiring. The small rows in the cost box show the honest shape of that bill — one named part, a stated slice of labour, and any call-out fee outside the figure, because no publishable basis for one exists.

Panel and service work

A panel upgrade is the complete version of the job: old load centre removed, new one set in the same position, every existing branch circuit transferred and re-terminated, the meter loop and service work the job includes, labelling, and the city inspection. In Austin it also means the Austin Energy approval and controlled outage described below — a second process running alongside the permit, with its own order of operations. Beyond the core scope, quotes diverge: extra breakers, a new meter base, mast work. Ask for those as itemised lines.

Small installs on existing wiring

The fan, GFCI and surge protector rows are swaps onto what already exists: a fan onto a box already rated to carry one, a device into a wired box, a protector into a panel with a breaker position to spare. A fitting that needs new wiring or a new rated box is a different job, and it is not priced on this page.

Permits in Austin: the city's Electrical Upgrade permit

Austin requires a permit for a panel upgrade, and it has a named permit type for exactly this job. Development Services (DSD) issues a stand-alone trade permit called "Electrical Upgrade" — for electrical upgrade work that does not require formal plan review — and the city's condition is printed with the type: you must be registered as a contractor before you apply. Trade permits are requested and issued to a State of Texas licensed professional contractor, and a licensed, registered trade contractor is required to request the electrical permit and be assigned to it. Registration comes first: before any work under a building or trade permit, the contractor registers with the city's Building and Trade Contractor Services, with an AB+C Portal account, a letter of authorisation, the state licence and master licence, and photo ID — registered once, updated annually.

The homeowner route exists in Austin — and the main service is carved out of it. Austin's Homestead Permit lets a qualifying homeowner perform their own trade work without a licence, but the city's Residential Permitting Guide states the limit in one sentence: "Only a registered electrician can get a permit if the electrical changes require making changes to the main electrical service," and the city's homeowner training lists "cannot work on the main electric service" among what the Homestead Permit does not cover. A panel and service upgrade is main-service work by definition. So the route is real for downstream work and closed for this job: the permit goes to a TDLR-licensed, city-registered contractor. And if a job's scope outgrows homestead qualifications mid-project, city code (§25-11-36) requires a licensed contractor to take over the permit.

About the permit fee, this page prints no number, and here is why. The city's FY 2026-27 residential fee schedule contains no line named for this permit — no "Electrical Upgrade", no panel or service-upgrade line, and no electrical equivalent of the change-out lines it prints for other trades — and the schedule document itself could not be read first-hand in this research. A fee assembled from second-hand readings of an unread schedule would be invented with extra steps. Rather than guess, we print the rule and not a total. What you can do: ask your contractor to show you the fee on the permit paperwork, and expect the permit line to appear, itemised, on your quote.

Austin's listed electrical code edition is the 2026 National Electrical Code, in force from September 1, 2026 — but on service work the NEC is not the only rulebook, which is the subject of the next section.

Austin Energy: the second mandatory desk

Austin is the one city in this group where the utility is a second permitting authority in practice, because Austin Energy is city-owned and approves your service separately from DSD's permit. If Austin Energy is your service provider, Development Services issues your electric service permit — but the permit depends on Austin Energy's approval first, through the Electrical Service Planning Application (ESPA). The ESPA is needed to obtain the permit: by signing it, Austin Energy confirms it can provide the load, voltage and infrastructure your job requests. A separate ESPA is required for every metered address, and the approved ESPA must be attached to the permit application. After the permit becomes active, Austin Energy visits the site to fix the point of attachment — the "spot location" — and service work must follow Austin Energy's Design Criteria Manual as well as the NEC; that manual's specifications are approved by the City Council, which gives them more than advisory weight. A 200-amp residential upgrade falls inside Austin Energy's "service-only" classification, and a Meter Review is also required before a meter is installed for a service upgrade.

The outage itself runs in a published order, and it is worth learning before your job starts:

  1. 1

    Austin Energy schedules a controlled outage — your contractor emails the utility's St. Elmo Distribution Dispatch to book it.

  2. 2

    The electrical inspection is scheduled for the outage.

  3. 3

    The service rebuild is performed after Austin Energy has de-energised the service.

  4. 4

    Once the Development Services inspection has passed, Austin Energy re-energises the service.

There is a contractor-run alternative. Under Austin Energy's Contractor Disconnect Program, a TDLR-licensed electrical contractor registered with DSD may also register with Austin Energy (approval runs one year) to cut the utility's seal and supply conductors for residential service rebuilds and main panel change-outs itself: DSD permit first, the outage booked seven days in advance, the meter removed and reinstalled only once, and once the inspection passes, the master electrician re-energises the service and fits a temporary seal, after which Austin Energy dispatches a meter technician to check the connections and install the permanent seal. In both paths the same gate holds: a passed city inspection comes before the power goes back on.

On money, this page states the position and prints no utility totals: Austin Energy publishes fee lines for service applications, reviews and connection work, but whether any given line applies to a like-for-like panel rebuild — as opposed to new service — is not stated in its published material, and its charges are set per project. Treat any Austin Energy charge as a line to have itemised on your paperwork, not as a figure any website can hand you in advance.

Choosing electricians in Austin, TX: the two-part licence check

Austin adds a city registration on top of the state licence, but the licence itself is Texas's, issued by TDLR and valid statewide. It takes two searches to check properly, because a company's record names its master without vouching for his status:

  1. 1

    Take the company's licence number from its truck, quote or invoice. In print it wears the TECL prefix; in TDLR License Search, enter it bare.

  2. 2

    Open the record titled Electrical Contractor (Type: EC). It should name the business you are dealing with, at its address and county, with status Active and an expiration date still to come.

  3. 3

    Read down to the "Master:" line. That line names the Master Electrician of Record, with his licence number and expiration.

  4. 4

    Now search for the master in his own right — by the name, or the number you just noted — and open the Master Electrician (Type: ME) record. Name and number must correspond, and his status must read Active and unexpired.

  5. 5

    Either record failing — expired, absent, mismatched — means the company is not currently legal to hire for electrical work, whatever its truck says.

  6. 6

    If you want the third layer, TDLR's final-orders search lists the enforcement actions taken against licensees.

Two requirements sit behind the records. A contractor must be, or employ, its master of record — and a master may be assigned to only one contractor at a time, unless he owns more than half of the business. The contractor must also maintain commercial general liability insurance of at least $300,000 per occurrence, $600,000 aggregate and $300,000 for products and completed operations, at all times. Then the Austin questions: is this contractor registered with the city, and who is handling the ESPA and the outage booking? Ask for the insurance certificate, get the quote in writing with its exclusions named, and keep the final payment until the inspection passes and the service is re-energised.

EV chargers in Austin: what we can price, and what we cannot

The charger itself prices cleanly. Two units carry verified prices, seen November 17, 2026: the ChargePoint Home Flex Level 2 charger at $599.00 (Home Depot) and the Tesla Wall Connector at $635.00 (Tesla's own store).

An installed total does not price cleanly, and this page does not publish one, because we could not verify one from primary sources. The cable run between panel and charger is the dominant cost, and its length is a property of your home — a few feet across a garage, or sixty feet across a house. We hold no verified retail price for the cable at the gauge these circuits need, nor for the two-pole breaker. And if your service cannot carry the load, the panel upgrade above becomes a prerequisite job — in Austin, with the ESPA and outage sequence that comes with it. Ask instead: what run length does the quote assume, are the breaker and permit inside it, and was your panel's capacity actually checked?

What changes the cost in Austin

Whether service work is part of the job

The benchmark example includes the meter loop and service work. Leave the service work out and the job is smaller and quicker — and in Austin it may also step around the Austin Energy approval and outage process that service work triggers. When two quotes for "a panel job" sit far apart, this scope line is the first place to look.

Breakers beyond the box

The guide's example starts from a value pack — main breaker plus five branch breakers. Circuits beyond the five need breakers the pack does not contain, and the inspector can require AFCI or GFCI breaker upgrades under the 2026 NEC on top. Those parts carry no verified retailer price in our research: expect them as a separate line on a real quote, and ask for it to be itemised.

Panel location and access

The benchmark keeps the panel where it is, on existing circuits of workable length. A panel that has to move, or service equipment that turns out to need mast or meter base work, falls outside the benchmark's scope and its total.

Timing: nights, weekends and peak season

Planned work is priced from ordinary hours. Fault-finding at night or on a weekend usually costs more; the premium is set by each company, with no published rate we can verify. Ask for the call-out basis before the visit, not after it.

Austin electrician questions

How much does a 200-amp panel upgrade cost in Austin?

This page publishes no Austin total, deliberately. The fully worked Texas example in the cost guide — a Square D Homeline value pack at $269.00 retail, a city permit, and 8–12 hours of labour built from BLS wage data under a stated 3.0-times assumption — comes to $1,090–$1,470, but the permit inside that figure is Houston's, and Austin's permit has no verifiable price (see the next answer). Use the benchmark to judge the shape of an Austin quote, not as the quote.

How much is the electrical permit for a panel upgrade in Austin?

No figure appears here, for a documentary reason. The permit itself is real — a stand-alone DSD "Electrical Upgrade" permit — but the city's FY 2026-27 residential fee schedule contains no line that prices it, and the schedule could not be read first-hand in this research. Austin Energy charges may also apply to the service side and are set per project. A single total from us would be assembled, not verified. The paperwork your contractor receives shows what the city actually charged.

Do I need a permit to replace my electrical panel in Austin?

Yes. A panel upgrade takes the stand-alone Electrical Upgrade permit from Development Services, requested by a licensed, city-registered electrical contractor, and the work is inspected — in Austin the passed inspection is also the gate that lets Austin Energy re-energise your service.

Can I pull my own permit for a panel upgrade in Austin?

No. Austin's Homestead Permit lets a qualifying homeowner do their own trade work, but the city's guidance excludes the main electrical service from it: only a registered electrician can get a permit where the work changes the main service, and a panel upgrade is exactly that work. The homestead route covers downstream jobs, not this one.

Why does Austin Energy have to approve my panel job as well as the city?

Because in Austin the utility and the permitting office are separate desks. Austin Energy must confirm, through the Electrical Service Planning Application, that it can supply the load and infrastructure your service needs — the approved ESPA is attached to your permit application — and it controls the outage and the re-energising. The order runs: ESPA, permit, controlled outage, rebuild, passed DSD inspection, then Austin Energy restores service. A contractor registered in the Contractor Disconnect Program can run the disconnect side itself, under the same inspection gate.

How do I check an electrician's licence in Austin?

Checked on TDLR License Search, in two parts. Start with the company's Electrical Contractor record (Type: EC) — Active, unexpired — and read its "Master:" line for the Master Electrician of Record. Then find that master's own Master Electrician record (Type: ME): the name and number must match, and his status must be Active too. Austin's separate requirement is city registration, which the permit itself proves: an unregistered contractor cannot apply for one.

How much does it cost to install an EV charger in Austin?

Only in pieces, because the pieces are what verify. The units: ChargePoint's Home Flex at $599.00, Tesla's Wall Connector at $635.00. The installed figure depends on the cable run from your panel to the charger — different in every home — and we hold no verified prices for the cable or the breaker, so any single range we printed would be invented.

Do Austin electricians charge a service-call or diagnostic fee?

Many do, but this page prints no figure for it. No official source publishes an Austin diagnostic fee, and TDLR licenses electricians without regulating their charges. Two questions before booking: what does the visit cost, and is the fee credited toward the repair if you proceed? Get both answers before anyone is dispatched.

Areas served in and around Austin

Tell us your neighbourhood when you request a quote, and we will match you with a professional who covers your part of the city.

When it lands, the list will describe the area this page serves for matching homeowners with professionals. It is this page's coverage statement — it says nothing about where any individual company will or will not travel.

Related services and other Texas cities

Disclaimer. The costs on this page are estimates only, computed from the sources below with their assumptions printed next to them. Your final price depends on your home, the job and the scope you agree, and costs vary by job, material and location. Always confirm a contractor's licence and insurance before work starts.

Sources

  • Texas Department of Licensing and Regulation — electrician licensing: contractor licence, Master Electrician of Record, insurance minimums, License Search and final-orders search (tdlr.texas.gov)
  • Texas Legislature — Occupations Code Chapter 1305, including §1305.151, §1305.201 and §1305.003(a)(6)
  • City of Austin, Development Services — Types of Permits (stand-alone "Electrical Upgrade"), Apply for a Standalone Permit, Contractor Registration, Homeowner's Permit and Residential Permitting Guide; Building Technical Codes (2026 NEC) (austintexas.gov / permittingatx.com)
  • Austin Energy — Apply for Electric Service (ESPA, Service Rebuilds outage sequence), Design Criteria Manual, Meter Review, Contractor Disconnect Program Terms & Conditions (austinenergy.com)
  • U.S. Bureau of Labor Statistics, OEWS May 2025 — electrician wages: Austin metro mean and Texas mean, both read from BLS (bls.gov)
  • Lowe's — Square D Homeline 200-amp load centre value pack, $269.00; Hunter Toledo 52-in ceiling fan, $126.00; Square D X Series GFCI receptacle, $41.84 — retail prices seen November 17, 2026
  • Schneider Electric USA — Square D HEPD80 surge protective device, manufacturer list price $185.00, seen November 17, 2026
  • The Home Depot — ChargePoint Home Flex Level 2 EV charger, $599.00, seen November 17, 2026; Tesla Shop — Wall Connector, $635.00, seen November 17, 2026
Call for a free quote Get a Quote