Electricians in Fort Worth, TX

TDLR-licensed contractors for panel work, repairs and installs — and a line Fort Worth draws more clearly than any other city in this group: a homeowner's own electrical work legally stops at the first main breaker, and a panel replacement sits on the contractor side of that line.

A panel with no spare space for the circuit you need, a breaker that trips under an ordinary load, a dead outlet in a room that matters — electricians in Fort Worth, TX cover that work in homes across the city. What this page will not do is print a Fort Worth permit fee: the city's current adopted fee schedule could not be opened from the city's own published link, so any figure would rest on a superseded schedule or a second-hand reading. What it does instead is show you the fully worked Texas benchmark with its basis labelled, the permit, registration and meter rules that are verified from the city's code and Oncor's own guidelines, and the licence check that takes five minutes.

How much does an electrician cost in Fort Worth?

Fort Worth electricians charge by the job. What follows are the Texas ranges from the electrician cost guide that this page can stand behind, each printed with the basis it stands on:

Job (Texas ranges from the cost guide)Range
200-amp panel upgrade or replacement, including meter loop and service work — guide's worked example, computed on Houston's permit schedule$1,090–$1,470
Whole-home surge protector, installed at the panel$270–$320 — plus the note below: the device is priced at manufacturer list
Ceiling fan replacement, on an existing fan-rated box$210–$305
GFCI receptacle replacement, one outlet on existing wiring$85–$130

Read the labels before you budget. The panel benchmark is a Texas worked example with Houston's permit inside it, because Houston's fee schedule could be verified line by line and Fort Worth's current one could not be opened at all — the permit section below explains the failure plainly rather than papering over it. Your Fort Worth permit fee will be a different number, set out on the permit paperwork your contractor receives. The three smaller rows travel better: each is assembled from an identified part at a dated retail price plus declared labour hours costed from wage data, which is what allows them to be stated for Texas generally; the surge protector's device is priced at the manufacturer's list price of $185.00, which is not a street price, and a retailer may charge less. A diagnostic or service-call fee is the one figure this page refuses to print: no official source publishes one, and TDLR's licence says nothing about prices.

One wage figure helps you read any Fort Worth quote. The U.S. Bureau of Labor Statistics puts the mean hourly wage for electricians across the Dallas-Fort Worth-Arlington metro — BLS publishes this area as one combined metro, not two cities — at $28.83 (OEWS, May 2025). Treat that as a wage and nothing more: what a company must charge per hour also has to carry payroll taxes, insurance, vehicle, overhead and margin, which is why the guide builds its labour maths on a stated multiplier over the wage rather than pretending the wage is the rate you will be charged.

  • Free quotes
  • No obligation
  • Licensed professionals
  • Texas-focused
Electrician working at an open residential breaker panel

Electrical emergency in Fort Worth: make it safe first

An electrical fault is a safety problem before it is a repair job. Work through these steps first, then call.

  • Sparks, crackling or buzzing from an outlet or switch: stop using that circuit. Switch its breaker off at the panel and leave the device alone until it has been checked.
  • A burning smell near the panel or an outlet: switch off the affected circuit — the main breaker if you cannot tell which circuit it is — and do not open the panel or investigate inside it. Call a licensed electrician.
  • The whole home has lost power: check your main breaker once. If it has not tripped and neighbouring homes are dark too, the outage is wider than your house; wait for power to return. If yours is the only dark home and the breaker looks fine, the fault may sit in your own service equipment — that is licensed work, not a DIY inspection.
  • A breaker that trips again right after a reset: do not keep resetting it. A breaker that will not stay on is reporting a fault on that circuit; leave it off and get the circuit checked.

After-hours work costs more than the same job in the working day, for a plain reason: a company pays more to staff nights and weekends. This page prints no call-out fee or after-hours premium, because none could be verified from primary sources, so agree that charge before the visit, not on the doorstep. Nor does anything here guarantee that a given company will pick up at a given hour.

What an electrician's visit covers — and what is included

Diagnosis and repairs

Diagnosis comes before parts. The electrician tests the circuit, then the device, then the breaker, working in an order that distinguishes a cheap failed component from a wiring fault. The small rows above model the honest version of that bill: a named part, declared labour hours, and the call-out fee outside the figure, because no publishable basis for one exists.

Panel and service work

A panel upgrade is the full version of this job: the old load centre out, the new one set in the same location, existing branch circuits transferred and re-terminated, the meter loop and service work the job includes, labelling, and the city inspection that permanent power hangs on. In Fort Worth it also means the permit and the Oncor meter authorisation described below, both arranged by your contractor before the meter is touched. Where quotes diverge is past that core — extra breakers, a new meter base, mast work. Get those lines itemised rather than folded into a lump sum, so one quote can be compared against another.

Small installs on existing wiring

Each of the three small rows assumes the infrastructure is already in place: an existing fan-rated box for the fan, existing wiring and a box for the GFCI device, a spare breaker slot for the protector. Work that has to create the box or the run is a different job, and it is deliberately not priced here.

Permits and contractor registration in Fort Worth

Fort Worth requires an electrical permit for a panel or service replacement. City code (Chapter 7, §105.1) requires a permit to install, alter, repair, remove, convert or replace any electrical system, and the exemption list in §105.2 does not reach this job — the only panel-adjacent exemption is replacing or repairing an overcurrent device of the required capacity in the same location: a like-for-like breaker swap, not a panel. The city's own residential permits brochure says the same in plain language: changing or replacing electrical work, including the replacement of an existing electric line, requires an electrical permit.

Who may hold the permit is set by the same chapter. Section 105.10 provides that electrical permits are issued only to companies or persons who hold the appropriate Texas state licences, and §118.1 requires a valid Contractor Registration on file for electrical permits — for an electrical registration, §118.1.3 requires the applicant to hold a valid State of Texas Electrical Contractor's licence. Registration is required and runs one year, but for state-licensed electricians it carries no fee: §118.2.1 sets a general annual registration fee and then exempts state-licensed plumbing, electrical and mechanical contractors from paying it, stating the point twice over — "State licensed electricians are exempt from paying registration fees." The exemption is from the fee, not from registering.

The homeowner line is the clearest in Texas, and it stops at the main breaker. Section 105.10 also lets an owner-occupier of a primary residence take out a building permit for their own work — but for electrical work the provision "only permits the homeowner to work on that part of the electrical system that occurs after, but does not include, the first main breaker behind the electrical meter." A 200-amp panel replacement is the first main breaker and the service equipment, and a meter loop sits on the meter side of it. So the boundary is not a grey area: downstream of the main breaker, a Fort Worth homeowner may legally do their own permitted work; the panel and service themselves are contractor-only, and their permit must be pulled by a TDLR-licensed, city-registered electrical contractor. It is the mirror image of Houston, where no homeowner electrical permit exists at all — Fort Worth allows the route and fences it.

On the fee itself, this page is silent — deliberately, and here is the documentary reason. Fort Worth's current adopted fee schedule (Ordinance 26-28781, effective October 1, 2026) could not be opened from official sources: the city's own published Development Fee Schedule link returned an error on the day this page was researched, and the code library's fee history still ends at the prior ordinance. The last openable schedule is superseded, and second-hand readings of the new one are not a basis we publish. Rather than dress a stale figure up as current, we print the rule and not a total. The check available to you is the paperwork: ask your contractor to show you the fee on the permit document itself, and expect the permit line to appear, itemised, on your quote.

Two process facts complete the picture. Permanent power is tied to the Electrical Final — the city's inspection guidance lists an inspection of the electrical system before the final for the purpose of permanent power, with temporary power handled as a separate release — and a Fort Worth permit expires after 180 days without an approved inspection (§105.5), so a stalled job can lose its permit. Fort Worth works to the 2026 National Electrical Code, effective in the city from September 1, 2026.

Oncor and the meter: authorisation before anyone touches it

Fort Worth's electricity delivery is Oncor's, and Oncor's published service guidelines put the meter pull in the contractor's hands — under authorisation, never casually. Before removing a self-contained meter, the electrical contractor calls Oncor (the guidelines publish the number: 1.800.518.2374) with the company and contact details, the address, the work to be done, whether an inspection is required, and the meter-pull and meter-replacement dates. Oncor then schedules its own trip to inspect and reseal after the meter goes back. Only Oncor may remove its meter locks, and the guidelines state the rule that protects you: Oncor will not interconnect its distribution system with your electrical installation until it receives notification that the proper authority — the city — has approved it.

The one published charge in this process is for doing it the unauthorised way: cutting the seal or removing a meter without prior authorisation charges the customer $19.20 minimum, and more where there is tampering or damage. No fee for an authorised meter pull or reseal is published in the guidelines, so none is printed here — if a quote carries a line for one, ask what it is based on. The sequence to hold your contractor to: authorisation call first, permitted work, city inspection and approval, then interconnection.

Choosing electricians in Fort Worth, TX: the two-part licence check

Fort Worth adds a city registration on top of the state licence, but the licence behind every Fort Worth electrician is a state licence — TDLR issues it, and it is valid anywhere in Texas. Two records have to agree before it means anything, because the company's record displays its master's name and number but not his standing:

  1. 1

    Note the licence number from the company's truck, quote or invoice. Printed there it carries the TECL prefix; drop the prefix when you search TDLR License Search.

  2. 2

    Call up the business's record — the heading reads Electrical Contractor (Type: EC). The business name, address and county should match the firm in front of you, with status Active and an expiration date that has not passed.

  3. 3

    On that same record, find the line beginning "Master:". It identifies the Master Electrician of Record, with his licence number and its expiration.

  4. 4

    Search once more, this time for the man himself — the record headed Master Electrician (Type: ME). His name and number must be the ones the contractor record showed, and his status must read Active with time left to run.

  5. 5

    If one record is expired, missing, or does not match the other, the company is not currently in order to hire — no matter what the truck says.

  6. 6

    TDLR also keeps a final-orders search: worth a minute, for fines or revocations against the name.

The shape of the rules explains the two records. A contractor must be a master or employ one as master of record, and a master can be attached to only one contractor at a time unless he owns more than half of it. The contractor must also carry commercial general liability insurance — $300,000 per occurrence, $600,000 aggregate, $300,000 products and completed operations — continuously. Fort Worth then adds its own question: is the contractor registered with the city? It must be, before any permit issues, even though state licensees pay no fee for it. Ask for the insurance certificate, get the quote in writing with its exclusions named, and hold the final payment until the Electrical Final passes.

EV chargers in Fort Worth: what we can price, and what we cannot

The units are the simple part. Two named chargers, prices seen November 17, 2026: ChargePoint's Home Flex at $599.00 (Home Depot) and Tesla's Wall Connector at $635.00 (Tesla's own store).

The installation resists a total, and this page does not offer one, because we could not verify one from primary sources. The run of cable between panel and charger dominates the job, and its length is fixed by your house, not by any standard: across a garage wall, or across the whole building. Our research holds no verified retail price for that cable or for the two-pole breaker, and where a panel has no spare capacity the charger drags a panel upgrade in behind it. Ask instead: what run length does the quote assume, are breaker and permit inside it, and did anyone actually check your panel's capacity?

What changes the cost in Fort Worth

Whether service work is part of the job

The benchmark example includes the meter loop and service work. Strip the service work out and the job shrinks — fewer hours, a different scope — so when two quotes for "a panel job" disagree, compare that line first.

Breakers beyond the box

The guide's example panel ships as a value pack: a main breaker and five branch breakers included. Every circuit beyond those five needs another breaker, and an inspector working to the 2026 NEC may require AFCI or GFCI types among them. We could verify no retailer price for those breakers, so on a real quote they belong on their own itemised line — ask for it if it is not there.

Panel location and access

The benchmark puts the new panel in the old panel's place, reusing circuits of workable length. A relocation, or service equipment that turns out to need mast or meter base work, moves the job outside the benchmark's scope and its total.

Timing: nights, weekends and peak season

The figures here are built on ordinary hours. The same fault found at night or on a weekend generally costs more; the premium is each company's own, and no published rate exists for us to verify. Settle the call-out basis before the visit, not after it.

Fort Worth electrician questions

How much does a 200-amp panel upgrade cost in Fort Worth?

This page publishes no Fort Worth total, deliberately. The fully worked Texas example in the cost guide — a Square D Homeline value pack at $269.00 retail, a city permit, and 8–12 hours of labour built from BLS wage data under a stated 3.0-times assumption — comes to $1,090–$1,470, but the permit inside that figure is Houston's, and Fort Worth's current fee schedule could not be opened from the city's own link (see the next answer). Use the benchmark to judge the shape of a Fort Worth quote, not as the quote.

How much is the electrical permit for a panel upgrade in Fort Worth?

We do not publish a figure; the obstacle is the document itself. The current adopted schedule (Ordinance 26-28781, in force from October 1, 2026) could not be opened from official sources — the city's published fee-schedule link returned an error when this page was researched — and the last openable schedule is superseded. A figure built on it, or on a second-hand reading of the new schedule, would be presented as current when we cannot show that it is. Your contractor's permit paperwork shows the fee the city actually charged.

Do I need a permit to replace my electrical panel in Fort Worth?

Yes. Replacing an electrical panel or service requires an electrical permit under Chapter 7, §105.1 of the city code, pulled by a state-licensed, city-registered contractor, and the work is inspected. The only panel-adjacent exemption is swapping a breaker for one of the required capacity in the same location — that does not cover a panel.

Can I replace my own panel in Fort Worth?

No — and Fort Worth's rule is the clearest in Texas on where your own work stops. An owner-occupier may take out a permit for their own electrical work only on the part of the system after, but not including, the first main breaker behind the meter (§105.10). A panel replacement is the first main breaker and the service equipment, so its permit must be pulled by a TDLR-licensed, city-registered electrical contractor.

Does Fort Worth charge electricians a registration fee?

Registration is required, the fee is not — for state licensees. Section 118.2.1 sets a general annual registration fee, then exempts state-licensed plumbing, electrical and mechanical contractors from paying it. Your electrician must still be registered and current before a permit issues; the exemption is from the fee, not from registering.

Who pulls the meter for a panel job in Fort Worth, and what does it cost?

Your contractor arranges it, under Oncor's authorisation process: the contractor calls Oncor before removing a self-contained meter, with the job details and the pull and replacement dates, and Oncor schedules a trip to inspect and reseal afterwards. Oncor will not interconnect until the city has approved the installation. No fee for an authorised pull is published in Oncor's guidelines; the one published charge is $19.20 minimum for removing a meter or cutting a seal without authorisation.

How do I check an electrician's licence in Fort Worth?

In two lookups on TDLR License Search. First, the business's Electrical Contractor record (Type: EC) — it should be Active and unexpired, and its "Master:" line names the Master Electrician of Record. Second, that master's own Master Electrician record (Type: ME) — name and number matching the contractor record, status Active. Fort Worth adds city registration on top, and the permit proves it: an unregistered contractor cannot pull one.

Do Fort Worth electricians charge a service-call or diagnostic fee?

Commonly, yes — but the amount is not printed here. No official source publishes a Fort Worth diagnostic fee, and TDLR licenses electricians without regulating what they charge. Before you book, ask the price of the visit and whether it is credited toward the repair if you proceed, and get both answers before anyone is dispatched.

Areas served in and around Fort Worth

Tell us your neighbourhood when you request a quote, and we will match you with a professional who covers your part of the city.

When it lands, the list will describe the area this page serves for matching homeowners with professionals. It is this page's coverage statement — it says nothing about where any individual company will or will not travel. Fort Worth and Dallas share a metro but not a permitting office: if your home sits on the other side of the line, see electricians in Dallas, TX.

Related services and other Texas cities

Disclaimer. The costs on this page are estimates only, computed from the sources below with their assumptions printed next to them. Your final price depends on your home, the job and the scope you agree, and costs vary by job, material and location. Always confirm a contractor's licence and insurance before work starts.

Sources

  • Texas Department of Licensing and Regulation — electrician licensing: contractor licence, Master Electrician of Record, insurance minimums, License Search and final-orders search (tdlr.texas.gov)
  • Texas Legislature — Occupations Code Chapter 1305, including §1305.151, §1305.201 and §1305.003(a)(6)
  • City of Fort Worth — Code of the City of Fort Worth, Chapter 7 (§§105.1, 105.2, 105.5, 105.10, 118.1, 118.1.3, 118.2.1); Residential Building Permits brochure; Permits page (2026 NEC adoption) (fortworthtexas.gov)
  • Oncor Electric Delivery — Electric Service Guidelines: meter-pull authorisation, inspection-before-interconnect rule, unauthorised-removal charge (oncor.com)
  • U.S. Bureau of Labor Statistics, OEWS May 2025 — electrician wages: Dallas-Fort Worth-Arlington metro mean and Texas mean, both read from BLS (bls.gov)
  • Lowe's — Square D Homeline 200-amp load centre value pack, $269.00; Hunter Toledo 52-in ceiling fan, $126.00; Square D X Series GFCI receptacle, $41.84 — retail prices seen November 17, 2026
  • Schneider Electric USA — Square D HEPD80 surge protective device, manufacturer list price $185.00, seen November 17, 2026
  • The Home Depot — ChargePoint Home Flex Level 2 EV charger, $599.00, seen November 17, 2026; Tesla Shop — Wall Connector, $635.00, seen November 17, 2026
Call for a free quote Get a Quote