HVAC Replacement Cost in Texas: One Complete Job, Priced in the Open
Ask what HVAC replacement cost in Texas should be and the answers swing by thousands of dollars, with no page showing its arithmetic. This guide works differently: it prices one complete job end to end — a named equipment package at a real retail price, labour built from published wage data under a stated assumption, and a real city's permit — then explains every factor that moves a quote away from that benchmark, and names the repairs it cannot honestly price at all.
- Free quotes
- No obligation
- Licensed professionals
- Texas-focused
How much does HVAC replacement cost in Texas?
Replacing a complete 3-ton split system — condenser, evaporator coil and gas furnace — in a Houston home runs $5,900–$6,300 installed on the worked example below: a $4,705.37 equipment package, 12–16 hours of labour built from Bureau of Labor Statistics wage data, and Houston's mechanical permit. Smaller jobs price differently; one common repair, a run capacitor swap, computes to $75–$120 before any trip fee.
That is a benchmark, not a Texas average — no honest statewide average exists, because system size, equipment tier and scope move the total more than geography does. Read the example to see what a complete job is made of, then hold any real quote against it line by line. For repairs and companies by city, start from the Texas HVAC hub.

HVAC costs by job
| Job | Cost | How the range is built |
|---|---|---|
| Full system replacement, 3-ton split system, installed | $5,900–$6,300 | Goodman package — GLXS4MA3610 condenser, CHPTA3630C3 coil, GRVT800804CN gas furnace — at $4,705.37 retail, plus 12–16 hours of labour on the wage-based build below, plus Houston's mechanical permit (2% of job value + $47.00 + $33.56). Ductwork, line set, thermostat and haul-away excluded; full example below |
| Run capacitor replacement | $75–$120 | AmRad USA2236 dual run capacitor (45 + 5 µF), $31.18 retail, plus 0.5–1.0 hour of on-site labour. Any trip or diagnostic fee is extra and is not included — no publishable basis for one exists |
How to read the labour in every row. No row here quotes a market hourly rate, because we could not source one we can stand behind. Labour is built from wage data instead. The U.S. Bureau of Labor Statistics puts the mean wage for heating, air conditioning and refrigeration mechanics at $29.03 an hour in the Houston metro and $28.43 statewide (OEWS, May 2025) — wages, not billable rates, since they exclude payroll taxes, benefits, insurance, vehicles, overhead and margin. Our examples build the billable rate as wage × 3.0 ($87.09 on the Houston basis, $85.29 on the Texas basis), cross-check every total on both, and print that multiplier wherever totals appear. The hour bands are stated assumptions too: no authoritative install-time standard exists, so the band is the sensitivity.
Why the table has two rows, not twelve. Every other job we attempted — condenser-and-coil replacement, contactor, blower motor, compressor, refrigerant work — failed verification for a stated reason, set out in the "does not price" section below. A short table we can defend beats a long one we cannot.
How the cost is calculated
Equipment: the package is the largest line
In the worked example, $4,705.37 of a roughly $6,100 job is equipment before an hour of labour is counted. A complete replacement buys a matched set — condenser, coil and furnace or air handler that are designed and rated to work together — and the set's price turns on capacity (tonnage), efficiency rating, and brand and model. Sizing deserves one caution: the right capacity comes from a load calculation for your home (the industry method is Manual J), not from copying the old unit's tonnage or from a square-footage guess. An oversized system costs more to buy and short-cycles in use; ask any bidder whether a load calculation sits behind the size they are quoting.
Labour: hours, built from a wage
Labour is hours × a billable rate, and both halves deserve scrutiny on any quote. The wage data anchors the rate: an employer pays the wage, but the business also carries insurance, a vehicle, tools and margin before an hour can be sold to you — the gap the declared 3.0 multiplier stands in for. The hours are set by the job's shape: the example assumes a two-technician crew for one working day to recover the old refrigerant, remove three components, set and level the new ones, braze and pressure-test the connections, evacuate the lines, charge the system and commission it. Work that fights back — a coil in a tight attic, a furnace in a closet — stretches those hours.
Permits: a city fee on a published basis
Texas issues no state installation permit; the state licenses the contractor through TDLR, and cities issue permits. The example is set in Houston because its schedule is the one this guide verified: a mechanical permit and inspection are required for air conditioning replacement, and on the alteration basis — the fit where existing ductwork is reused — the fee is 2% of the total job cost plus $47.00, plus a $33.56 administration fee, which is why the permit line in the example moves with the job value instead of sitting at a flat figure. Other Texas cities set their own schedules and bases; this guide states a fee only for Houston.
Scope: what a "replacement" quote leaves out
The totals here assume the existing ductwork, refrigerant line set, pad location and thermostat are reused, and they exclude haul-away of the old system. Those exclusions are where real quotes diverge: one company's "system replacement" includes duct modification and disposal, another's quietly leaves both out, and the second quote looks cheaper until the extras land. The checklist below exists to force that difference into the open before you sign.
Worked example: replacing a complete 3-ton system in Houston
The job, with its assumptions stated: a like-for-like replacement of a complete 3-ton split system in a single-family Houston home — new condenser, new cased evaporator coil, new 80% AFUE gas furnace — reusing the existing ductwork, refrigerant line set, pad location and thermostat. The equipment is a Goodman package: GLXS4MA3610 condenser (single-stage, R-32, rated 14.3 SEER2 — exactly the federal floor for this size in Texas, covered next), CHPTA3630C3 cased evaporator coil, and GRVT800804CN furnace (80,000 BTU, 80% AFUE), bought as one matched retail bundle. Houston is the setting because its permit schedule and wage basis are the ones this guide verified.
| Line | Amount | Basis |
|---|---|---|
| Equipment package | $4,705.37 | Retail price for that bundle, seen November 17, 2026 — retail prices change |
| Labour | $1,045.08–$1,393.44 | 12–16 hours (stated assumption: two-technician crew, one working day) at $87.09 an hour — the Houston mean wage of $29.03 × the declared 3.0 assumption |
| Permit | $195.57–$202.54 | Houston mechanical permit, Alteration of HVAC basis: 2% of (equipment + labour) + $47.00 + $33.56 |
| Total | $5,900–$6,300 | Rounded from the two computations below |
Computed two independent ways, the totals agree. Method 1 (Houston wage basis): labour at $87.09 an hour over 12–16 hours gives $1,045.08–$1,393.44; job value $5,750.45–$6,098.81; permit $195.57–$202.54; totals $5,946.02–$6,301.35, midpoint $6,123.69. Method 2 (Texas statewide wage, $28.43 × 3.0 = $85.29 an hour): labour $1,023.48–$1,364.64; permit $195.14–$201.96; totals $5,923.99–$6,271.97, midpoint $6,097.98. The midpoints sit $25.71 apart, about 0.4%, and the ranges overlap almost entirely — that overlap, rounded, is the published $5,900–$6,300.
Not in this total: ductwork modification or replacement; a replacement line set (the existing set is reused, and the condenser ships factory-charged for 15 feet of tubing); a new thermostat; electrical panel or breaker upgrades; condensate pump or drain rework; haul-away and disposal of the old system; and any refrigerant beyond the factory charge. Each is excluded because we hold no verified price for it — not because your job will never need one.
The SEER2 floor: why efficiency rules shape replacement cost
SEER2 is the current federal efficiency measure for air conditioners, and Texas sits in the Department of Energy's Southeast region, where the standard runs on the installation date. For a split-system air conditioner installed on or after January 1, 2023, the minimum is 14.3 SEER2 for systems under 45,000 BTU an hour of cooling capacity — a 3-ton system is 36,000, so 14.3 is the floor for most Texas homes — and 13.8 SEER2 at or above that capacity. Split-system heat pumps must meet 14.3 SEER2 and 7.5 HSPF2 nationwide.
Three consequences matter when you price a replacement. First, the floor is a floor: it is illegal for a contractor to install a unit below the regional standard, so "the same efficiency as the old one" is not an available option on an older, low-rated system — every legal quote starts at today's minimum. Second, SEER2 numbers are measured under a newer test procedure and are not directly comparable to the old SEER ratings on your existing unit's label; a like-for-like comparison of the two numbers misleads. Third, the example system's 14.3 SEER2 rating is the minimum, not a premium tier — higher-rated equipment exists and costs more, and any claim about what a higher rating saves on bills depends on your home and usage, so treat savings projections as estimates to test, not as facts.
One caution from our own verification: even the equipment retailer selling the example package headlines it with a higher efficiency figure than its own condenser specification states. Check the model number's rated SEER2, not the headline.
What this guide does not price — and why
Condenser-and-coil replacement as a standalone job. The condenser alone carries an open retail price, but the matching evaporator coil's price sits behind trade-account logins at the distributors we checked. Splitting the worked example's bundle price to invent the coil's share would be fabrication, so the pair gets no row until an open coil price exists.
Contactor, blower motor and compressor replacements. Each turns on a named part at a checkable retail price, and for these three we could not ground one: the listings found were bulk-import offers, decade-old catalogues, or ranges too wide across motor and compressor types to bound with a stated assumption. They will be priced when the Plumbing cluster's method — named part, real price, stated hours — can run on them honestly.
Refrigerant recharge, per pound or per job. Three separate reasons. Federal law restricts refrigerant sales for home equipment to EPA Section 608-certified technicians, so no consumer retail price exists to anchor a row. Cylinder prices observed during verification were unstable and contradictory across sources and seasons. And the quantity a job needs depends on system size, line length and the state of the leak, so no stated assumption can bound it. Published per-pound figures elsewhere are contractor price claims, not sources. What is true and useful: a system needing repeated top-ups has a leak, and finding and fixing the leak is the repair.
Diagnostic, service-call and trip fees. No authoritative source publishes one, and TDLR does not regulate HVAC prices. That is why the capacitor row prints its exclusion instead of folding in a fee we invented: expect a trip or diagnostic charge on most real invoices, and get its amount before the visit.
Until those jobs can be built from sources, judge a quote on its structure. A quote you can audit names the equipment by model, states the labour, shows the permit line or explains why none applies, and lists its exclusions. A single lump figure with none of that behind it is not a bargain or a rip-off — it is unauditable, and you can ask for the breakdown before you agree.
What a complete quote must include
Hold any replacement quote against this list, drawn from what a complete job actually contains:
- Condenser, evaporator coil and furnace or air handler, each by brand and model number
- The efficiency rating of the matched system (SEER2), and the load calculation behind the size
- Refrigerant line set — reused or replaced, stated either way
- Pad, disconnect and any electrical work the job needs
- The permit: who pulls it, its fee, and the inspection that follows
- Haul-away and disposal of the old equipment
- Warranty terms, split into the equipment warranty and the labour warranty
- Exclusions, named — ductwork is the one most often left silent
Repair or replace: the questions that decide it
No honest rule of thumb settles this — the popular formulas multiply two numbers and call the product a verdict, and none of them knows your system. Ask these instead:
What exactly has failed? A single component — a capacitor, a control — on a system that has otherwise run well is a repair. A failed compressor or a leaking coil is a major-component event, and it changes the conversation.
How has the system behaved lately? Your own history is data: a system that has needed repeated call-outs in recent seasons is telling you something a formula cannot.
What does the repair quote come to against the replacement benchmark? You can do this arithmetic yourself: set the written repair quote beside the $5,900–$6,300 complete-job benchmark above, with scopes matched. The ratio is information; it is not a rule, and anyone who converts it into one is selling.
Will the replacement have to meet today's floor anyway? It will — 14.3 SEER2 for most Texas homes. If the old system is far below that, replacement buys a step up in rated efficiency as a by-product; whether that step is worth money to you depends on your bills, which only you can see.
Are parts and service for your system still straightforward? Ask the contractor directly whether the failed part is readily available for your model, and whether the refrigerant your system uses is still serviced without difficulty. Their answer, in writing, is worth more than a generic age limit.
Get both quotes in writing, itemised the same way, and compare scope before totals.
Mistakes that make replacement cost more
- Comparing totals instead of scope. Two quotes for "a new system" can differ on the coil, the line set, the permit, haul-away and the warranty. Line them up item by item — the checklist above — before deciding one is cheaper.
- Sizing by the old unit or by square footage. Capacity should come from a load calculation. An oversized system costs more up front and short-cycles; an undersized one runs constantly and still disappoints.
- Reading the headline efficiency instead of the model's rating. Our own verification caught a retailer headline that overstated its package's SEER2. Check the model number's specification.
- Paying to recharge a leaking system, repeatedly. The refrigerant is not the fault; the leak is. Each top-up without a leak repair is money spent standing still.
- Skipping the permit to save the fee. In Houston the permit and inspection are required for a replacement, and the inspection is your independent proof the work was done to code.
HVAC replacement questions
How much does it cost to replace an HVAC system in Texas?
For the complete job this guide can verify — a 3-ton split system, condenser, coil and gas furnace, installed in a Houston home with the permit — $5,900–$6,300. The figure is a worked example built from a named $4,705.37 equipment package, wage-based labour under a stated assumption, and the city's permit basis, not a survey of quotes; other sizes, tiers and scopes move it, in the directions the factors section describes.
What is the minimum SEER2 for a new air conditioner in Texas?
Texas is in the federal Southeast region, where the standard runs on installation date: a split-system air conditioner installed on or after January 1, 2023 must meet 14.3 SEER2 if it is under 45,000 BTU an hour of capacity — most home systems, including 3-ton — and 13.8 SEER2 at or above that capacity. Split-system heat pumps must meet 14.3 SEER2 and 7.5 HSPF2. Installing below the standard is illegal for the contractor.
Do I need a permit to replace my HVAC system?
Texas has no state installation permit — the state licenses the contractor through TDLR, and permits are issued by cities. Houston requires a mechanical permit and an inspection for air conditioning replacement, pulled by a contractor registered with the city; on the alteration basis its fee is 2% of the job cost plus $47.00 plus a $33.56 administration fee. Your city sets its own rules, so ask the bidder who pulls the permit and whether its fee is in the quote.
Why is there no price here for refrigerant or a compressor?
Because neither could be built from a checkable source. Refrigerant may legally be sold only to EPA-certified technicians, so no consumer price exists to anchor a figure, and cylinder prices are unstable besides; for compressors, no named unit at an open retail price could be grounded during verification. Rather than borrow an aggregator's average, this guide leaves the row empty and says why.
How do I check an HVAC contractor's licence in Texas?
Ask for the company's TACLA or TACLB number and search it in the TDLR License Search. Confirm the record is an ACR Contractor licence — a technician registration is not a licence to contract — with Active status, and that the class and the E or C endorsement cover your job. Then run the name through TDLR's final-orders search for enforcement actions, and ask to see the certificate of insurance the licence requires.
Can I buy refrigerant and recharge my system myself?
No. Under EPA Section 608, refrigerant for home air conditioning equipment may be purchased only by certified technicians — Type II certification covers residential split systems — and the service work itself belongs to certified technicians working under a licensed contractor. Venting refrigerant is prohibited. A system that keeps losing charge has a leak to find and fix.
Find HVAC help in your city
You have the benchmark and the method; the next step is a person. Start from Texas HVAC companies, services and licensing, or go straight to your city — AC repair in Houston, with the permit rules that shape its prices, AC repair in Dallas, TX, HVAC services in Fort Worth, AC repair in Austin, TX, AC repair in San Antonio, TX, heating and cooling in El Paso. Ready for your own number? Get a free HVAC quote — or see what a plumber costs in Texas.
Disclaimer. The costs on this page are estimates only, computed from the sources below with their assumptions printed next to them. Your final price depends on your home, the job and the scope you agree, and costs vary by job, material and location. Always confirm a contractor's licence and insurance before work starts.
Sources
- U.S. Department of Energy, Appliance Standards Program — 2023 CAC Standards FAQ: Southeast region SEER2 minimums, installation-date compliance (energy.gov)
- Texas Department of Licensing and Regulation — ACR contractor licensing: classes, endorsements, insurance minimums, License Search and final-orders search (tdlr.texas.gov)
- City of Houston, Houston Permitting Center — mechanical inspections for air conditioning replacement; Alteration of HVAC instrument HPWCODE1019, fee basis (houstonpermittingcenter.org)
- U.S. Bureau of Labor Statistics, OEWS May 2025 — heating, air conditioning and refrigeration mechanic wages, Houston metro and Texas (bls.gov; cross-checked via the U.S. Department of Labor's O*NET republication of BLS OEWS)
- U.S. Environmental Protection Agency — Section 608 refrigerant sales restriction (epa.gov)
- Home Outlet Direct — Goodman 3-ton split system package GLXS4MA3610 / CHPTA3630C3 / GRVT800804CN, retail price seen November 17, 2026
- HVAC & Tools Direct — AmRad USA2236 dual run capacitor, retail price seen November 17, 2026
