Electrician Cost in Texas: What Each Job Is Made Of

Search for an electrician cost in Texas and you will find ranges for the same panel upgrade that disagree by thousands of dollars, with no method shown behind any of them. This guide takes the other route. Every range below is assembled from a named part at a dated retail or manufacturer price, labour hours costed from published wage data under one stated assumption, and a city's own permit schedule where a permit applies. Find your job in the table, then read how its number was built.

  • Free quotes
  • No obligation
  • Licensed professionals
  • Texas-focused

How much does an electrician cost in Texas?

There is no single electrician cost in Texas, so this guide prices named jobs instead: replacing one GFCI outlet computes to $85–$130, a ceiling-fan swap on an existing rated box to $210–$305, and a full 200-amp panel upgrade in Houston to $1,090–$1,470, permit included.

That spread is the honest answer. A one-device swap and a permitted service upgrade are different jobs sharing a trade, and averaging them into a single figure hides the only part that helps you: what your job is made of. For the statewide picture — services, licensing, choosing a company — see the Texas electricians hub.

Electrician working at an open residential breaker panel

Electrician costs by job

JobCostHow the range is built
Panel upgrade or replacement to 200 amps, installed (Houston, including meter loop and service work)$1,090–$1,470Square D Homeline value pack, $269.00 retail, plus the City of Houston permit at $136.95, plus 8–12 hours of labour. Worked in full below. Plan-review fee and breakers beyond the value pack excluded
Whole-home surge protector, installed at the panel$270–$320Square D HEPD80 at the manufacturer list price of $185.00 — list is not a street price, and a retailer may charge less — plus 1–1.5 hours of labour. A two-pole breaker, if none is spare in your panel, is excluded
Ceiling fan replacement (existing fan-rated box)$210–$305Hunter Toledo 52-inch fan, $126.00 retail, plus 1–2 hours of labour. A new fan-rated box or brace, and any new wiring, excluded
GFCI receptacle replacement (one outlet, existing wiring)$85–$130Square D X Series GFCI receptacle, $41.84 retail, plus 0.5–1 hour of labour. Priced as professional work — see the legal note below the table
EV charger, Level 2 — charger unit only$599–$635 (unit prices)ChargePoint Home Flex, $599.00; Tesla Wall Connector, $635.00. Installation is not priced — the EV section below explains why
Diagnostic / service callNot pricedNo official source publishes a Texas diagnostic fee, and TDLR does not regulate prices
Ceiling fan — new installation, no existing box or wiringNot pricedThe box, brace and wiring inputs could not be verified from named sources
Standard outlet or switch replacementNot pricedNo named standard-device retail price was verified for this guide
Whole-home rewire / new circuit runsNot pricedNo groundable per-foot cable price or bounded labour basis exists

How to read the labour in every row. No row here quotes a market hourly rate, because we could not source one we can stand behind. Labour is built from wage data instead. The U.S. Bureau of Labor Statistics puts the Houston metro mean electrician's wage at $29.55 an hour (OEWS, May 2025) — a wage, not a billable rate, since it excludes payroll taxes, benefits, insurance, vehicles, overhead and margin. Our examples build the billable rate as wage × 3.0 = $88.65 an hour, and cross-check every total on a second basis: the Texas mean wage of $28.50 an hour (× 3.0 = $85.50), read from BLS itself (OEWS Query System, May 2025). Both bases are means, so the cross-check compares like with like — a metro wage against the statewide wage on the same statistic. The hour bands are assumptions as well — no official install-time standard exists for any of these jobs, so treat the band itself as the margin for error.

The legal note on the GFCI row. That range is the price of having the work done professionally, and in Texas that is not a stylistic choice. Hired electrical work must be performed by a licensed electrician working through a licensed electrical contractor (Occupations Code §1305.151). The exemption in §1305.003(a)(6) covers only work in a dwelling by a person who owns and resides in it — the full boundary is drawn in the DIY section below.

How the cost is calculated

Labour: hours, the licence ladder, and one declared multiplier

Labour is hours × a billable rate, and both halves deserve scrutiny on any quote. The hours are set by the job's scope; the rate is set by who does the work and what the business carries. Texas structures that workforce by licence: apprentices and residential wiremen at the entry rungs, journeymen above them, and a Master Electrician at the top — and every electrical contractor must be, or employ, a master as its Master Electrician of Record. A quote's labour line reflects that structure whether it says so or not: the company is selling supervised, licensed time, plus the insurance, vehicle and overhead the wage data leaves out. That gap is what our declared 3.0 multiplier stands in for.

Hourly versus flat-rate follows from this. Companies quote small, well-defined jobs flat, because the hours are predictable; fault-finding is often charged by time or by a diagnostic visit, because the hours are not. Our table builds every row as parts + hours, which is the test to apply to a flat quote: ask what part is in it, and how many hours it assumes.

Parts: the name on the box, and the kind of price

For replacements, the part is often the largest single line: $269.00 for the load centre in the panel example, $126.00 for the fan, $41.84 for the GFCI device. Price type matters as much as the number. Most rows here use retail prices seen on November 17, 2026. One does not: no retailer price could be verified for the surge protector, so its row is built on the manufacturer's list price of $185.00 and says so — list prices sit at or above what retailers charge, and a row built on one should be read with that in mind. The same discipline explains an absence: the panel example uses the value pack because its retail price could be verified, while the same load centre sold without the bundled breakers could not be priced from a retailer at all.

Permits: a city fee from a published schedule

Where a permit applies, the fee is the city's, set by a published schedule — not a markup the company invents. This guide states a fee for Houston only, the one schedule verified for it: a panel job with meter loop and service work computes to $136.95 from three printed lines, and the worked example below shows them. Other Texas cities set their own schedules, and a fee from Houston's schedule should never be quoted as another city's.

Access and scope: the hours you cannot see in a catalogue

Every row assumes the fast case: like-for-like work on existing connections, in the same location, with the panel or box reachable. A panel that must move, a circuit run that crosses a finished house, a box that turns out not to be fan-rated — each converts a priced swap into unpriced scope. Access and scope, not the part, are where a firm quote after inspection most often parts company with a published standard-case range.

Worked example: the 200-amp panel upgrade, in full

The job, with its assumptions stated: replacement of the existing panel with a 200-amp service in a single-family Houston home, new panel in the same location, including meter loop and service work up to 50 kW, permit pulled by a TDLR-licensed, City-registered electrical contractor, and a City of Houston inspection. Equipment: a Square D Homeline 200-amp, 40-space, 80-circuit load centre value pack (model HOM4080M200PCVP), which includes the 200-amp main breaker and five branch breakers per the manufacturer's datasheet.

LineAmountBasis
Panel (value pack)$269.00Lowe's retail price, seen November 17, 2026
Permit$136.95City of Houston 2026 schedule: $94.00 meter loop and service (up to 50 kW) + $9.39 panel with eight or more circuits + $33.56 administration fee
Labour$709.20–$1,063.808–12 hours (stated assumption: service disconnect and changeover coordination, old panel out, new load centre set, existing circuits transferred and re-terminated, labelling, inspection attendance) at $88.65 an hour
Total$1,090–$1,470Rounded from the two computations below
  • Method 1 (Houston wage basis): labour at $88.65 an hour — the BLS Houston metro mean wage of $29.55 × the declared 3.0 assumption — gives totals of $1,115.15 at 8 hours and $1,469.75 at 12 hours.
  • Method 2 (Texas wage basis): labour at $85.50 an hour — the Texas mean wage of $28.50 × 3.0 — gives totals of $1,089.95 and $1,431.95. The midpoints of the two methods sit about 2.5% apart, and the rounded overlap is the published range.

Not in this total: branch breakers beyond the five in the value pack (no verified retail price exists for them); AFCI or GFCI breaker upgrades if the inspector requires them; meter base replacement; service mast or underground lateral work beyond the meter-loop scope; any CenterPoint Energy fee (none was verified); drywall or paint repair; a surge protector (priced as its own row above); and any plan-review fee — Houston may assess one on a valuation basis, the schedule states no computable electrical amount, so it is excluded and disclosed rather than estimated. A panel-only job, with no meter loop or service work, would carry a different permit: the $9.39 panel fee falls under the schedule's $91.06 minimum, making the permit $124.62.

The Houston money page carries this same example in its city context: electricians in Houston, TX.

EV charger costs: the unit is the only honest number

A Level 2 charger is the job readers most often ask us to total, and it is the one this guide refuses to. What verifies cleanly: the units — a ChargePoint Home Flex at $599.00 (Home Depot) and a Tesla Wall Connector at $635.00 (Tesla's own store), both seen November 17, 2026 — and one permit line, Houston's schedule price of $100.71 for a Level 2 charging outlet, before that schedule's administration fee and minimum structure.

What does not verify is everything that decides the installed figure. The circuit run from panel to charger is the dominant cost, and its length is a property of your home — a few feet across a garage or sixty feet across a house. We hold no verified retail price for the cable at the gauge these circuits need, nor for the two-pole breaker. And if your service cannot carry the load, the panel upgrade above becomes a prerequisite job. A range printed across those unknowns would be a guess wearing a table's clothing, so the installed total is not published, because we could not verify one from primary sources. Ask instead: what run length does the quote assume, are the breaker and permit inside it, and was your panel's capacity actually checked?

Doing the work yourself: where Texas law draws the line

Texas law starts from a licensing rule, not a DIY permission. Under Occupations Code §1305.151, a person or business may not perform, or offer to perform, electrical work unless they hold the appropriate licence — and hired work runs through a licensed electrical contractor.

The exemption, §1305.003(a)(6), is narrow and has two locks on it. It covers work performed in or on a dwelling by a person who owns and resides in that dwelling — both conditions, not either — and only work "not specifically regulated by a municipal ordinance". Read against real life, that means the exemption does not reach:

  • a rental property you own but do not live in;
  • a house you are renovating to sell;
  • work in a relative's or a friend's home;
  • anything done by a person you hire, licensed or not — hiring is what §1305.151 governs.

The municipal lock is not theoretical. Houston specifically regulates electrical work, and its Electrical Code (§302.1) allows only a licensed and registered electrical contractor to obtain an electrical permit. The Permitting Center publishes homeowner permits for plumbing and mechanical work; it publishes no homeowner electrical permit, and its only electrical application requires a master electrician's signature. In Houston, panel and service work is contractor work however the state exemption reads. Other cities write their own rules — check yours before assuming the exemption is the whole answer.

Factors that change the cost

Panel capacity and whether service work is included

The panel example is an upgrade to 200 amps with meter loop and service work, and its permit ($136.95) and hours reflect that scope. A like-for-like panel swap with no service work carries the $124.62 permit basis instead and fewer hours. When two quotes for "a new panel" sit far apart, this scope line is the first place to look.

Breakers: count, type, and the inspector

The value pack's five branch breakers will not fill a 40-space panel. Additional breakers are a real cost this guide could not verify a retail price for, and AFCI or GFCI breaker upgrades required at inspection add more. Houston works to the 2023 National Electrical Code, effective January 1, 2024 — the last completed Houston adoption we could verify — while Texas adopted the 2026 NEC statewide effective September 1, 2026, and Houston's own move to the 2026 edition was still a published proposal when we checked. Work is inspected against the adopted edition where the job is, not the edition your panel was installed under.

Distance: runs, relocations and new circuits

Parts-plus-hours pricing holds while the job stays where the wiring already is. Every foot of new run — a charger across the house, a panel relocation, a new circuit — adds cable, time and often wall repair, none of which a standard-case range can carry. This factor is the whole EV story above.

Timing

Work booked ahead is priced from ordinary hours. The same job at night, on a weekend or in an emergency usually costs more, because staffing unsocial hours costs more — but no official source publishes an emergency premium, and none is priced here. Settle the call-out basis before the visit.

Common mistakes when comparing electrician quotes

  • Comparing totals without comparing scope. One panel quote includes service work, the permit and inspection; another is the box and the swap alone. Lay the lines side by side — equipment, permit, breakers, service work — before comparing the bottom numbers. Published ranges disagree for the same reason: they are pricing different jobs under one name.
  • Treating a TECL number as the whole licence check. The number on the truck identifies the company's contractor licence — part one. The company's Master Electrician of Record has his own licence, with its own status, and only his own record shows it. Run both searches; the hub teaches them step by step.
  • Hiring an individual licence as if it were a contractor licence. A journeyman's or even a master's licence authorises the person; the business offering you the work needs the Electrical Contractor licence behind it, with insurance filed at TDLR's minimums — $300,000 per occurrence, $600,000 aggregate, $300,000 products and completed operations.
  • Booking a diagnostic without settling its terms. Ask what the visit costs and whether the fee is credited toward the repair if you proceed — before dispatch, not on the doorstep. No published standard exists to fall back on.

What this guide does not price — and why

  • Diagnostic and service-call fees. No regulator, city or standards body publishes one, and TDLR does not regulate what electricians charge. Any figure would be a marketing claim copied from the companies being priced.
  • Emergency and after-hours premiums. Real, but set company by company with no authoritative basis. Explained qualitatively above; never numbered.
  • EV charger installation. The run length is home-specific and unboundable, and the cable and breaker prices could not be verified. Units and the permit line only.
  • New ceiling fan installation. Only the replacement variant cleared: the fan-rated box, brace and wiring a new install needs have no verified prices.
  • Standard outlet and switch replacement. Only the GFCI device was priced from a named retail listing; no standard-device price was verified.
  • Rewires and per-foot circuit pricing. No groundable per-foot cable price or bounded labour basis was obtained.
  • A Texas "average" for anything. The wage data supports worked examples for named jobs. It does not support an average cost of an electrician, and this guide does not print one.

Texas electrician cost questions

How much does an electrician cost in Texas?

By the job. The four jobs this guide can build from named parts and wage data: a GFCI outlet replacement at $85–$130, a ceiling fan swap on an existing rated box at $210–$305, a whole-home surge protector at $270–$320 on a manufacturer list price, and a 200-amp panel upgrade in Houston at $1,090–$1,470, permit included. Jobs we cannot ground — diagnostics, rewires, charger installs — carry no figure, and the reasons are stated rather than papered over.

What is an electrician's hourly rate in Texas?

No sourced market rate exists, and this guide does not present one. What exists is wage data: the BLS OEWS May 2025 mean wage for Houston metro electricians is $29.55 an hour, and the Texas mean is $28.50. A wage is an employer's cost before insurance, vehicles, overhead and margin, so a billable rate is always higher. Our examples build one openly — wage × 3.0, giving $88.65 and $85.50 — and label it an assumption every time. Treat any page that states a Texas hourly rate as fact with suspicion.

Why do quotes for the same panel upgrade differ so much?

Because "panel upgrade" hides at least four scope decisions: whether meter loop and service work is included, how many and what type of breakers are in the price, whether the permit and any plan-review fee are carried, and whether the panel stays in its location. Our worked example prices one stated version — $1,090–$1,470 — and prints its exclusions. Ask each quoting company to itemise against the same list and the disagreement usually explains itself.

Is it legal to hire an unlicensed electrician in Texas?

No. Non-exempt electrical work must be performed by a licensed person working through a licensed electrical contractor (§1305.151). The owner-occupier exemption in §1305.003(a)(6) covers work you do yourself in a home you own and live in; it does not extend to anyone you hire, and it does not cover rentals or homes you are renovating to sell. An unlicensed hire also has no TDLR-filed insurance standing behind the work.

Can I replace my own electrical panel in Texas?

The state exemption is narrower than it sounds: your own work, in a dwelling you own and live in, and only where a municipal ordinance does not specifically regulate the work. Houston regulates it — only a licensed, registered contractor can obtain an electrical permit there (§302.1), and no homeowner electrical permit exists. In Houston the answer is no; elsewhere, your city's ordinance decides, so check it before relying on the exemption.

How much does it cost to install a Level 2 EV charger in Texas?

The verifiable parts: charger units at $599.00 (ChargePoint Home Flex) and $635.00 (Tesla Wall Connector), and Houston's permit line for a Level 2 charging outlet at $100.71. An installed total is not published here, because the circuit run that dominates it is different in every home and the cable and breaker prices could not be verified. Get quotes that state the assumed run length and whether panel capacity was checked.

Conclusion: price the job, not the trade

An electrician's price is not a number about a trade; it is a number about your job — its parts, its hours, its permit, its distance from your panel. Price it that way: name the job, ask for the lines, run the two-part licence check, and be wary of any total whose ingredients nobody will show you. When you are ready, call for a quote or start from the electricians hub and your city's page — Houston's is electricians in Houston, TX, and the same method is set out for the other five cities there. For another trade priced the same way, see the Texas plumber cost guide.

Disclaimer. The costs on this page are estimates only, computed from the sources below with their assumptions printed next to them. Your final price depends on your home, the job and the scope you agree, and costs vary by job, material and location. Always confirm a contractor's licence and insurance before work starts.

Sources

  • Texas Department of Licensing and Regulation — electrician licensing: contractor and individual licence types, Master Electrician of Record rule, insurance minimums, License Search and final-orders search; 2026 NEC adoption, 16 TAC §73.100, effective September 1, 2026 (tdlr.texas.gov)
  • Texas Legislature — Occupations Code Chapter 1305, including §1305.151, §1305.201, §1305.003(a)(6) and §1305.101
  • U.S. Bureau of Labor Statistics, OEWS May 2025 — electrician wages: Houston metro mean and Texas mean, both read from BLS (OEWS Query System)
  • City of Houston, Houston Permitting Center — 2026 Permit Fee Schedule, electrical section; Houston Electrical Code, Administrative Code Provisions for the 2023 NEC (houstonpermittingcenter.org)
  • Lowe's — Square D Homeline 200-amp load centre value pack, $269.00; Hunter Toledo 52-in ceiling fan, $126.00; Square D X Series GFCI receptacle, $41.84 — retail prices seen November 17, 2026
  • Schneider Electric USA — Square D HEPD80 surge protective device, manufacturer list price $185.00, seen November 17, 2026
  • The Home Depot — ChargePoint Home Flex Level 2 EV charger, $599.00, seen November 17, 2026; Tesla Shop — Wall Connector, $635.00, seen November 17, 2026
Call for a free quote Get a Quote