AC Repair in Houston, TX
Licensed Texas contractors for cooling repairs and full system replacements — one benchmark job, a complete 3-ton system swap, runs $5,900–$6,300 installed in the worked example below, and a single capacitor repair computes to $75–$120 before any trip fee.
A system that blows warm air in July, a condenser that hums and will not start, a furnace question saved for winter — AC repair in Houston, TX covers that work in homes across the city. This page prices the two jobs we can build from checked sources, walks through the permit the city requires for a replacement, gives you the county's own heat-safety steps for a home without cooling, and teaches the licence check that tells you whether the company at your door is legal to hire.
How much does AC repair cost in Houston?
AC repair in Houston, TX ranges from small component work to a full system changeout. The two jobs priced from checked sources on this page: replacing a failed run capacitor runs $75–$120 for the part and the on-site labour, with any trip or diagnostic fee extra, and replacing a complete 3-ton system runs $5,900–$6,300 installed, permit included. Other repairs carry no figure until they can be built the same way.
| Job | Installed cost |
|---|---|
| Full system replacement, 3-ton split system (condenser, coil, gas furnace) | $5,900–$6,300 |
| Run capacitor replacement | $75–$120 — plus any trip/diagnostic fee, which is not priced here |
Those are the only two ranges on this page, because they are the only two built from named parts at real retail prices, published wage data and the city's own permit schedule. Compressor, blower motor, contactor and refrigerant work carry no figure, because none could be verified from primary sources. Job-by-job reasoning sits in the Texas HVAC replacement cost guide.
- Free quotes
- No obligation
- Licensed professionals
- Texas-focused

No cooling in a Houston home: what to do first
A house without air conditioning in Houston heat is not just uncomfortable — treat it as time-sensitive, especially with an older adult, an infant, or anyone with a chronic condition in the home.
First, the checks that cost nothing: thermostat set to cool and below the room temperature, a clean filter in the slot, the breaker for the air handler and condenser switched on. If the outdoor unit hums but the fan does not turn, or the breaker trips again after one reset, stop there — the fault is electrical or mechanical, and it belongs to a licensed contractor.
While you wait, follow Harris County Public Health's heat guidance:
- Drink water frequently through the day, even if you do not feel thirsty; go easy on caffeine, alcohol and sugary drinks.
- Rest in air-conditioned or shaded places regularly, above all during the peak afternoon heat — if your home is not cooling, that means a public indoor space or a cooling centre; Harris County's list is at readyharris.org.
- Limit outdoor activity during the hottest part of the day, and wear loose, lightweight, light-coloured clothing.
- Check on family members and neighbours who are more vulnerable — older adults, infants, pregnant people, outdoor workers, anyone with a chronic condition.
- Never leave a child or a pet in a vehicle.
- Know the signs of heat illness: dizziness, headache, nausea, heavy sweating, confusion, a rapid heartbeat, muscle cramps. If symptoms worsen or heat-stroke signs appear, get medical attention immediately.
Emergency and out-of-hours work usually costs more than the same repair booked ahead, because the labour is bought at unsocial hours. We publish no call-out fee or after-hours premium: no official source sets one, and TDLR does not regulate what HVAC companies charge; we could not verify a figure for either from primary sources. Ask for the trip charge and the after-hours basis before you agree to the visit, and note that this page makes no promise about any particular company's hours.
What an HVAC visit covers — and what is included
Repairs: finding the failed part
A repair visit starts with diagnosis: the technician works through the thermostat signal, the electrical components in the outdoor unit, airflow at the indoor coil, and the refrigerant circuit, in an order that separates a cheap failed part from an expensive one. The capacitor row in the cost box is the honest shape of a small repair — one named part, a stated slice of on-site labour, and a trip fee that sits outside the figure because no publishable basis for it exists.
Replacement: the whole system, matched
A full replacement on this page means the matched set: outdoor condenser, indoor evaporator coil, and furnace — sized to the home, set and levelled, brazed and pressure-tested, evacuated, charged and commissioned. In Houston it also means a mechanical permit and a city inspection before the job is finalised. What it does not include here: ductwork changes, a new line set, a new thermostat, or electrical panel work — the exclusions are printed with the example below.
Refrigerant work: certified hands only
Refrigerant sits behind a federal gate. Under EPA Section 608, only certified technicians may purchase refrigerant for home air conditioning equipment or open the circuit that holds it — Type II certification covers residential split systems — and knowingly venting refrigerant is prohibited. A system that needs topping up again and again has a leak; the repair is finding and fixing the leak, and no lawful do-it-yourself refill exists.
Worked example: a Houston 3-ton system replacement, priced step by step
The job, with its assumptions stated: a like-for-like replacement of a complete 3-ton split system in a single-family Houston home — new condenser, new cased evaporator coil, new gas furnace — reusing the existing ductwork, refrigerant line set, pad location and thermostat. The equipment is a Goodman package: GLXS4MA3610 condenser (single-stage, R-32, rated 14.3 SEER2), CHPTA3630C3 cased coil, and GRVT800804CN furnace (80,000 BTU, 80% AFUE), sold as one matched bundle.
| Line | Amount | Basis |
|---|---|---|
| Equipment package | $4,705.37 | Retail price for that bundle, seen November 17, 2026 — retail prices change |
| Labour | $1,045.08–$1,393.44 | 12–16 hours (stated assumption: a two-technician crew for one working day — recovery, removal, setting, brazing, evacuation, charging, commissioning) at $87.09 an hour — the Houston wage × the declared 3.0 assumption, see below |
| Permit | $195.57–$202.54 | City of Houston mechanical permit on the Alteration of HVAC basis: 2% of the job value (equipment + labour) plus $47.00 plus a $33.56 administration fee |
| Total | $5,900–$6,300 | Rounded from the two computations below |
The labour rate needs its assumption in the open. The U.S. Bureau of Labor Statistics puts the mean wage for heating, air conditioning and refrigeration mechanics in the Houston metro at $29.03 an hour (OEWS, May 2025). A wage is not a billable rate: it excludes payroll taxes, insurance, vehicle, overhead and margin. We build the rate as $29.03 × 3.0 = $87.09 an hour. That multiplier is our stated assumption, not a market quote — no verified Houston billable rate exists, and this page never presents $87.09 as one.
Computed two independent ways, the totals agree. Method 1 (Houston wage basis): labour of $1,045.08–$1,393.44 over equipment of $4,705.37 gives a job value of $5,750.45–$6,098.81; the permit at 2% plus $80.56 comes to $195.57–$202.54; totals run $5,946.02–$6,301.35. Method 2 (Texas statewide wage, $28.43 × 3.0 = $85.29 an hour): labour runs $1,023.48–$1,364.64, the permit $195.14–$201.96, and totals $5,923.99–$6,271.97. The midpoints sit $25.71 apart — about 0.4% — and the rounded overlap is the published $5,900–$6,300.
One figure to read carefully: the equipment bundle is rated 14.3 SEER2, taken from the condenser's own specification. One retail listing headlines this package at a higher efficiency number; the unit's described rating is 14.3, which is also exactly the federal minimum for a 3-ton system installed in Texas, explained in the cost guide.
Not in this total: ductwork modification or replacement, a replacement line set (the existing set is reused; the condenser ships charged for 15 feet of tubing), a new thermostat, electrical panel or breaker upgrades, condensate pump or drain rework, haul-away of the old system, and any refrigerant beyond the factory charge — each excluded because we hold no verified price for it, not because your job will never need one.
Permits and inspections in Houston
Houston requires a mechanical permit — and an inspection — for residential air conditioning replacement, condenser replacement included. Texas itself issues no state installation permit: the state licenses the contractor through TDLR, and the permit is a city matter.
The permit is pulled by the contractor, who must be licensed and registered with the City of Houston before pulling it. For an alteration of an existing system — the basis this page's example uses, since the ductwork is reused — the city's fee is 2% of the total job cost plus $47.00, plus a $33.56 administration fee, and the permit stays valid for 180 days. A mechanical inspector must inspect and approve the work before the project is finalised. If a replacement quote has no permit line, ask why — and keep the final payment until the inspection passes.
What changes the cost in Houston
The equipment you choose
The bundle sets the floor: $4,705.37 of the worked example is equipment before an hour of labour is counted. A higher-efficiency or larger system moves that line directly, and since January 2023 nothing below the federal floor for this region — 14.3 SEER2 for a system under 45,000 BTU an hour — may legally be installed at all.
Scope beyond a like-for-like swap
The example reuses ductwork, line set, pad and thermostat. A job that replaces or modifies any of those adds parts and hours the total does not carry, which is why a firm price given before anyone has looked at the existing installation should be read as a guess.
The permit basis
The permit is a percentage fee, so it scales with the job: 2% of value plus fixed fees on the alteration basis used here. A job classed by the city as a complete new system rather than an alteration is priced on a different basis — one more reason the permit line belongs on the written quote, itemised.
Timing: nights, weekends and peak season
A repair booked ahead in normal hours is priced from ordinary labour. The same work at night, on a weekend, or in the middle of a heat spell usually costs more — the premium is real, but it is set by each company, and no published rate exists that we can verify and pass on.
Mistakes Houston homeowners make when hiring an HVAC company
- Hiring on a technician's registration card. The credential that authorises a company to contract is the TDLR ACR contractor licence. A registered technician must work under one; the card alone is not a licence to sell you work.
- Accepting a lump-sum replacement quote. No equipment models, no permit line, no exclusions — nothing to compare against the worked example above or against a second quote.
- Paying for repeated refrigerant top-ups. Each refill without a leak repair buys a few weeks of cooling and another bill. The leak is the repair.
- Letting a no-cool house wait with vulnerable people in it. Use the county's heat steps above, and a cooling centre if the home is not cooling — the repair decision can be made from somewhere safe.
- Skipping the permit to save the fee. The inspection is your independent proof the replacement was done to code, and the permit is the contractor's to pull, not yours to waive.
How to choose an HVAC company in Texas
Check the licence: the TDLR two-part check
Texas HVAC contracting is licensed by the Texas Department of Licensing and Regulation (TDLR) under Occupations Code Chapter 1302. Part one is the licence itself:
1. Get the company's licence number — TACLA (Class A) or TACLB (Class B) — from its truck, bid, invoice or website.
2. Open the TDLR License Search and search by that number, or by name and city.
3. Open the record and confirm it is an Air Conditioning and Refrigeration Contractor licence — not a technician registration — with status Active and a date that has not expired.
4. Confirm the class and endorsement cover your job: Class A covers any size; Class B covers cooling up to 25 tons and heating up to 1.5 million BTU an hour, which includes home systems; the endorsement should be E (Environmental Air Conditioning) or C (combined).
5. Run the same name through TDLR's final-orders search to see enforcement actions — fines, suspensions, revocations.
Part two is the paperwork behind the licence. The contractor licence requires commercial general liability insurance, maintained for as long as the licence is active: at Class A, $300,000 per occurrence, $600,000 aggregate, and $300,000 for products and completed operations; at Class B, $100,000 / $200,000 / $100,000. Ask to see the certificate of insurance before work starts — do not accept a verbal "we're covered".
And remember the company rule: an HVAC company must employ a licensed ACR contractor at each permanent location. TDLR's guidance is blunt — a company that does not cannot collect a fee or enforce its contract with you.
Questions to ask before work starts
- What is your TDLR contractor licence number, and whose name and business does the record show?
- Is the quote itemised — equipment by model, labour, permit — and what does it exclude?
- Who pulls the Houston mechanical permit, and is the inspection included?
- What does the diagnosis cost if I decline the repair — stated before the visit, not after?
- What warranty covers the equipment, and what covers your labour?
For the statewide picture, see all HVAC companies in Texas, and for other trades in this city, home services in Houston, TX.
Houston HVAC questions
How much does AC repair cost in Houston?
It depends on what has failed, and this page prices only what it can build from sources: a run capacitor replacement runs $75–$120 for the named part and on-site labour, with any trip or diagnostic fee extra, and a complete 3-ton system replacement runs $5,900–$6,300 installed with the permit. Compressor, motor and refrigerant figures are omitted until they can be verified the same way.
How much does it cost to replace a whole AC system in Houston?
For the benchmark job worked in full on this page — a 3-ton Goodman condenser, coil and gas furnace package at $4,705.37 retail, 12–16 hours of labour on a stated wage-based assumption, and Houston's mechanical permit — $5,900–$6,300 installed. Ductwork, a new line set, a thermostat and haul-away are excluded, so compare quotes only when the scopes match.
Do I need a permit to replace my air conditioner in Houston?
Yes. Houston requires a mechanical permit and an inspection for air conditioning replacement, condenser replacement included. The contractor pulls it — licensed contractors register their licence with the City of Houston first — and on the alteration basis the fee is 2% of the job cost plus $47.00 plus a $33.56 administration fee. Texas has no state installation permit; permits are a city matter.
How do I check whether a Houston HVAC company is licensed?
Ask for the TACLA or TACLB licence number, then search it in the TDLR License Search. Confirm the record is a contractor licence with Active status, that the class and the E or C endorsement cover your job, then check TDLR's final-orders search for enforcement actions and ask to see the insurance certificate. A technician registration card is not a licence to contract.
Can I top up my own refrigerant?
No. EPA Section 608 restricts refrigerant sales for home air conditioning equipment to certified technicians — Type II certification covers residential split systems — and the service work itself must be done by certified technicians under a licensed contractor. Venting refrigerant is prohibited, and repeated top-ups mean a leak that needs finding, not a refill routine.
What efficiency does a new system in Houston have to meet?
Texas sits in the federal Southeast region. For a split-system air conditioner installed on or after January 1, 2023, the minimum is 14.3 SEER2 under 45,000 BTU an hour of capacity and 13.8 SEER2 at or above it; split-system heat pumps must meet 14.3 SEER2 and 7.5 HSPF2. Compliance runs on the installation date, and a contractor may not legally install a unit below the standard.
What should I do while I wait for a repair in a hot house?
Follow Harris County Public Health's guidance: drink water frequently even before you feel thirsty, rest in air-conditioned or shaded places through the peak afternoon heat, limit outdoor activity, and check on older adults, infants and anyone with a chronic condition. If the home is not cooling, use a public indoor space or a cooling centre — the county list is at readyharris.org — and never leave children or pets in a vehicle.
Do HVAC companies in Houston charge more for emergency or after-hours calls?
Usually, yes — the reason is labour bought at unsocial hours, not the repair itself. What we cannot give you is a figure: no official source publishes a Houston call-out fee or after-hours premium, and TDLR does not regulate prices. Ask the trip charge before you book the visit.
Areas served in and around Houston
Tell us your neighbourhood when you request a quote, and we will match you with a professional who covers your part of the city.
The list, once verified, describes the Houston area this page covers for matching a homeowner with a professional — a coverage area for this page, not a claim about any one company's service area.
Related services and other Texas cities
Disclaimer. The costs on this page are estimates only, computed from the sources below with their assumptions printed next to them. Your final price depends on your home, the job and the scope you agree, and costs vary by job, material and location. Always confirm a contractor's licence and insurance before work starts.
Sources
- Texas Department of Licensing and Regulation — ACR contractor licensing: classes, endorsements, insurance minimums, License Search and final-orders search (tdlr.texas.gov)
- City of Houston, Houston Permitting Center — mechanical inspections for air conditioning replacement; Alteration of HVAC instrument HPWCODE1019, fee basis (houstonpermittingcenter.org)
- Harris County Public Health — summer heat safety guidance, June 2026; Harris County OEM (ReadyHarris) — cooling centres (readyharris.org)
- U.S. Department of Energy — 2023 central air conditioner standards FAQ: Southeast region SEER2 minimums (energy.gov)
- U.S. Environmental Protection Agency — Section 608 refrigerant sales restriction (epa.gov)
- U.S. Bureau of Labor Statistics, OEWS May 2025 — heating, air conditioning and refrigeration mechanic wages, Houston metro and Texas (bls.gov; cross-checked via the U.S. Department of Labor's O*NET republication of BLS OEWS)
- Home Outlet Direct — Goodman 3-ton split system package GLXS4MA3610 / CHPTA3630C3 / GRVT800804CN, retail price seen November 17, 2026
- HVAC & Tools Direct — AmRad USA2236 dual run capacitor, retail price seen November 17, 2026