AC Repair in San Antonio, TX

Licensed Texas contractors for cooling repairs and full system replacements in San Antonio homes — a complete 3-ton system swap, worked line by line below, runs $5,800–$6,200 installed with the city's permit built fee by fee inside the total, and a single capacitor repair computes to $75–$120 before any trip fee.

A condenser that stops on the hottest afternoon of the month, a system that cools one end of the house and abandons the other, a heating question saved for the first cold night — AC repair in San Antonio, TX covers that work in homes across the city. This page prices the jobs we can build from checked sources, shows the city permit fee being assembled line by line from the city's own schedule — the only city in this group where that is possible — and teaches the licence check, plus San Antonio's free state-licence registration, that tells you whether the company at your door is legal to hire.

How much does AC repair cost in San Antonio?

AC repair in San Antonio, TX stretches from small component work to a full system changeout. The two jobs priced from checked sources on this page: replacing a failed run capacitor runs $75–$120 for the part and the on-site labour, with any trip or diagnostic fee extra, and replacing a complete 3-ton system runs $5,800–$6,200 installed, permit included, in the worked example below. Other repairs carry no figure until they can be built the same way.

JobInstalled cost
Full system replacement, 3-ton split system (condenser, coil, gas furnace)$5,800–$6,200
Run capacitor replacement (Texas range from the cost guide)$75–$120 — plus any trip/diagnostic fee, which is not priced here

Those are the only two ranges on this page, because they are the only two built from named parts at real retail prices, published wage data and the city's own fee schedule. The capacitor row is the cost guide's Texas range: it is built from a named part and a stated slice of labour, with no permit in it, so it holds in San Antonio as it does statewide. Compressor, blower motor, contactor and refrigerant work carry no figure, because none could be verified from primary sources. Job-by-job reasoning sits in the Texas HVAC replacement cost guide.

  • Free quotes
  • No obligation
  • Licensed professionals
  • Texas-focused
Technician servicing an outdoor air-conditioning unit beside a home

No cooling in a San Antonio home: what to do first

A house without air conditioning in Texas heat is not just uncomfortable — treat it as time-sensitive, especially with an older adult, an infant, or anyone with a chronic condition in the home.

First, the checks that cost nothing: thermostat set to cool and below the room temperature, a clean filter in the slot, the breaker for the air handler and condenser switched on. If the outdoor unit hums but the fan does not turn, or the breaker trips again after one reset, stop there — the fault is electrical or mechanical, and it belongs to a licensed contractor.

While you wait for help: drink water regularly, spend the hottest part of the day in the coolest room or in an air-conditioned public place if the house is not cooling, check on family members and neighbours who cope badly with heat, and never leave a child or a pet in a vehicle. Dizziness, confusion, nausea or a racing heartbeat in the heat are reasons to get medical attention, not to wait the repair out.

Emergency and out-of-hours work usually costs more than the same repair booked ahead, because the labour is bought at unsocial hours. We publish no call-out fee or after-hours premium: no official source sets one, and TDLR does not regulate what HVAC companies charge; we could not verify a figure for either from primary sources. Ask for the trip charge and the after-hours basis before you agree to the visit, and note that this page makes no promise about any particular company's hours.

What an HVAC visit covers — and what is included

Repairs: finding the failed part

A repair visit starts with diagnosis: the technician works through the thermostat signal, the electrical components in the outdoor unit, airflow at the indoor coil, and the refrigerant circuit, in an order that separates a cheap failed part from an expensive one. The capacitor row in the cost box is the honest shape of a small repair — one named part, a stated slice of on-site labour, and a trip fee that sits outside the figure because no publishable basis for it exists.

Replacement: the whole system, matched

A full replacement on this page means the matched set: outdoor condenser, indoor evaporator coil, and furnace — sized to the home, set and levelled, brazed and pressure-tested, evacuated, charged and commissioned. In San Antonio it also means a standalone mechanical trade permit, applied for by the licensed professional doing the work. What it does not include here: ductwork changes, a new line set, a new thermostat, or electrical panel work — the exclusions are printed with the example below.

Refrigerant work: certified hands only

Refrigerant sits behind a federal gate. Under EPA Section 608, only certified technicians may purchase refrigerant for home air conditioning equipment or open the circuit that holds it — Type II certification covers residential split systems — and knowingly venting refrigerant is prohibited. A system that needs topping up again and again has a leak; the repair is finding and fixing the leak, and no lawful do-it-yourself refill exists.

Heating work

The same Texas licence covers the heating side: furnaces and heat pumps are air conditioning and refrigeration contracting work under state law, and the Class B licence limit for heating — 1.5 million BTU an hour — sits far above anything in a San Antonio home. A company you hire for a summer repair is licensed, if it is licensed at all, for the furnace question in winter too.

Worked example: a San Antonio 3-ton system replacement, priced step by step

The job, with its assumptions stated: a like-for-like replacement of a complete 3-ton split system in a single-family San Antonio home — new condenser, new cased evaporator coil, new gas furnace — reusing the existing ductwork, refrigerant line set, pad location and thermostat. The equipment is a Goodman package: GLXS4MA3610 condenser (single-stage, R-32, rated 14.3 SEER2), CHPTA3630C3 cased coil, and GRVT800804CN furnace (80,000 BTU, 80% AFUE), sold as one matched bundle — the same equipment the cost guide prices for its Houston example, so the two cities can be compared line by line.

LineAmountBasis
Equipment package$4,705.37Retail price for that bundle, seen November 17, 2026 — retail prices change
Labour$1,023.84–$1,365.1212–16 hours (stated assumption: a two-technician crew for one working day — recovery, removal, setting, brazing, evacuation, charging, commissioning) at $85.32 an hour — the San Antonio wage × the declared 3.0 assumption, see below
Permit$89.55City of San Antonio FY 2027 schedule, built line by line in the permit section below
Total$5,800–$6,200Rounded from the two computations below

The labour rate needs its assumption in the open. The U.S. Bureau of Labor Statistics puts the mean wage for heating, air conditioning and refrigeration mechanics in the San Antonio-New Braunfels metro at $28.44 an hour (OEWS, May 2025). A wage is not a billable rate: it excludes payroll taxes, insurance, vehicle, overhead and margin. We build the rate as $28.44 × 3.0 = $85.32 an hour. That multiplier is our stated assumption, not a market quote — no verified San Antonio billable rate exists, and this page never presents $85.32 as one.

Computed two independent ways, the totals agree almost exactly. Method 1 (San Antonio wage basis): labour of $1,023.84–$1,365.12 over equipment of $4,705.37 plus the $89.55 permit gives totals of $5,818.76–$6,160.04. Method 2 (Texas statewide wage, $28.43 × 3.0 = $85.29 an hour): labour runs $1,023.48–$1,364.64, and totals $5,818.40–$6,159.56. The midpoints sit $0.42 apart — the two wage bases nearly coincide for San Antonio — and the rounded range is the published $5,800–$6,200.

One figure to read carefully: the equipment bundle is rated 14.3 SEER2, taken from the condenser's own specification. One retail listing headlines this package at a higher efficiency number; the unit's described rating is 14.3, which is also exactly the federal minimum for a 3-ton system installed in Texas, explained in the cost guide.

Not in this total: ductwork modification or replacement, a replacement line set (the existing set is reused; the condenser ships charged for 15 feet of tubing), a new thermostat, electrical panel or breaker upgrades, condensate pump or drain rework, haul-away of the old system, and any refrigerant beyond the factory charge — each excluded because we hold no verified price for it, not because your job will never need one.

Permits and licence registration in San Antonio

San Antonio requires a permit for an HVAC replacement in an existing home: the job is a standalone mechanical (MEP) trade permit, and the city's FY 2027 fee schedule prices it in the section for heating and air conditioning work in existing residences — a section whose item list expressly covers "replacement of any device which originally required a permit." The licensed professional applies for their own standalone permit. Texas itself issues no state installation permit: the state licenses the contractor through TDLR, and the permit is a city matter.

San Antonio's schedule is itemised, so this page can do what the other city pages cannot — show the fee being built:

Permit line (FY 2027 schedule)Amount
Mechanical permit base fee$57.50
Condensing unit (per item)$7.19
Cooling coil (per item)$7.19
Gas furnace (per item)$11.04
Subtotal$82.92
Surcharges: 4% Technological Improvement + 4% Development Services (× 1.08)—
Permit total$89.55

The example's equipment is three devices — condenser, cased coil, furnace — and the schedule charges each one. The total assumes the permit is filed online: the schedule's $11.50 convenience fee applies only to non-online applications and its $3.45 inspection-scheduling fee only when the inspection is not scheduled online, so both are excluded here; a credit-card percentage is a payment-method charge, not a permit fee, and is excluded as well.

The licence layer has a San Antonio quirk worth knowing. The city's schedule states plainly that a state mechanical licence issued by Texas — the TDLR ACR licence — is required to perform mechanical work in San Antonio, and that there is no fee to register a state licence with the city. The city alternatively issues its own City Mechanical Master licence at $172.50 a year; a contractor needs one credential path or the other, and the state-licence path costs nothing to register. So when a San Antonio contractor shows you a TDLR licence, the city layer should already be in place — and free.

What changes the cost in San Antonio

The equipment you choose

The bundle sets the floor: $4,705.37 of the worked example is equipment before an hour of labour is counted. A higher-efficiency or larger system moves that line directly, and since January 2023 nothing below the federal floor for this region — 14.3 SEER2 for a system under 45,000 BTU an hour — may legally be installed at all.

Scope beyond a like-for-like swap

The example reuses ductwork, line set, pad and thermostat. A job that replaces or modifies any of those adds parts and hours the total does not carry, which is why a firm price given before anyone has looked at the existing installation should be read as a guess.

The permit, item by item

San Antonio's permit is a base fee plus a per-device charge plus two 4% surcharges, so it moves with the job's shape: a replacement that adds a device adds its line. The full build is printed above — hold your quote's permit line against it.

Timing: nights, weekends and peak season

A repair booked ahead in normal hours is priced from ordinary labour. The same work at night, on a weekend, or in the middle of a heat spell usually costs more — the premium is real, but it is set by each company, and no published rate exists that we can verify and pass on.

Mistakes San Antonio homeowners make when hiring an HVAC company

  • Hiring on a technician's registration card. The credential that authorises a company to contract is the TDLR ACR contractor licence. A registered technician must work under one; the card alone is not a licence to sell you work.
  • Accepting a lump-sum replacement quote. No equipment models, no permit line, no exclusions — nothing to compare against the worked example above or against a second quote.
  • Paying for repeated refrigerant top-ups. Each refill without a leak repair buys a few weeks of cooling and another bill. The leak is the repair.
  • Letting a sponsored ranking do the choosing. At least one San Antonio list on the web discloses that its top placement is sponsored. A ranking that is bought is an advertisement; the licence check below is free and takes five minutes.
  • Skipping the permit to save the fee. The permit is $89.55 on the worked example — a small line next to the equipment — and the inspection behind it is your independent proof the replacement was done to code. Pulling it is the contractor's job, not yours to waive.

How to choose an HVAC company in San Antonio

Check the licence: the TDLR two-part check

Texas HVAC contracting is licensed by the Texas Department of Licensing and Regulation (TDLR) under Occupations Code Chapter 1302. Part one is the licence itself:

1. Get the company's licence number — TACLA (Class A) or TACLB (Class B) — from its truck, bid, invoice or website.

2. Open the TDLR License Search and search by that number, or by name and city.

3. Open the record and confirm it is an Air Conditioning and Refrigeration Contractor licence — not a technician registration — with status Active and a date that has not expired.

4. Confirm the class and endorsement cover your job: Class A covers any size; Class B covers cooling up to 25 tons and heating up to 1.5 million BTU an hour, which includes home systems; the endorsement should be E (Environmental Air Conditioning) or C (combined).

5. Run the same name through TDLR's final-orders search to see enforcement actions — fines, suspensions, revocations.

Part two is the paperwork behind the licence. The contractor licence requires commercial general liability insurance, maintained for as long as the licence is active: at Class A, $300,000 per occurrence, $600,000 aggregate, and $300,000 for products and completed operations; at Class B, $100,000 / $200,000 / $100,000. Ask to see the certificate of insurance before work starts — do not accept a verbal "we're covered".

And remember the company rule: an HVAC company must employ a licensed ACR contractor at each permanent location. TDLR's guidance is blunt — a company that does not cannot collect a fee or enforce its contract with you.

Then note the San Antonio registration

San Antonio's city layer is the lightest in this group — and worth stating precisely, because contractors' paperwork varies by city. A state mechanical licence is required to do the work, the licensed professional applies for their own standalone permit, and registering that state licence with the City of San Antonio is free: the city's schedule says there is no fee to register a state license. (The alternative credential, the city's own Mechanical Master licence, costs $172.50 a year.) So the San Antonio check is the TDLR check above, plus one question: which credential path is this contractor on — a registered state licence, or the city's own master licence? Either is a real answer; hesitation is not.

Questions to ask before work starts

  • What is your TDLR contractor licence number, and whose name and business does the record show?
  • Is your state licence registered with the City of San Antonio, or do you hold the city's Mechanical Master licence?
  • Is the quote itemised — equipment by model, labour, permit — and what does it exclude?
  • What does the diagnosis cost if I decline the repair — stated before the visit, not after?
  • What warranty covers the equipment, and what covers your labour?

For the statewide picture, see all HVAC companies in Texas, and for other trades in this city, home services in San Antonio, TX.

San Antonio HVAC questions

How much does AC repair cost in San Antonio?

It depends on what has failed, and this page prices only what it can build from sources: a run capacitor replacement runs $75–$120 for the named part and on-site labour, with any trip or diagnostic fee extra, and a complete 3-ton system replacement runs $5,800–$6,200 installed with the permit, in the worked example above. Compressor, motor and refrigerant figures are omitted until they can be verified the same way.

How much does it cost to replace a whole AC system in San Antonio?

For the benchmark job worked in full on this page — a 3-ton Goodman condenser, coil and gas furnace package at $4,705.37 retail, 12–16 hours of labour on a stated wage-based assumption, and San Antonio's permit at $89.55 — $5,800–$6,200 installed. Ductwork, a new line set, a thermostat and haul-away are excluded, so compare quotes only when the scopes match.

Do I need a permit to replace my air conditioner in San Antonio?

Yes. An HVAC replacement in an existing San Antonio home is a standalone mechanical trade permit, and the licensed professional applies for their own permit. The city's schedule expressly prices "replacement of any device which originally required a permit." Texas has no state installation permit; permits are a city matter.

How much is the San Antonio permit for an AC replacement?

$89.55 for the worked example's job, built from the city's FY 2027 schedule: a $57.50 base fee, plus $7.19 for the condensing unit, $7.19 for the cooling coil and $11.04 for the gas furnace, with the schedule's two 4% surcharges applied — ($57.50 + $7.19 + $7.19 + $11.04) × 1.08 = $89.55. That assumes online filing; the fee is itemised, so a job with a different device count prices differently.

How do I check whether a San Antonio HVAC company is licensed?

Ask for the TACLA or TACLB licence number, then search it in the TDLR License Search. Confirm the record is a contractor licence with Active status, that the class and the E or C endorsement cover your job, then check TDLR's final-orders search for enforcement actions and ask to see the insurance certificate. In San Antonio, a state licence is required for the work and registering it with the city is free — the alternative is the city's own Mechanical Master licence. A technician registration card is not a licence to contract.

Can I top up my own refrigerant?

No. EPA Section 608 restricts refrigerant sales for home air conditioning equipment to certified technicians — Type II certification covers residential split systems — and the service work itself must be done by certified technicians under a licensed contractor. Venting refrigerant is prohibited, and repeated top-ups mean a leak that needs finding, not a refill routine.

What efficiency does a new system in San Antonio have to meet?

Texas sits in the federal Southeast region. For a split-system air conditioner installed on or after January 1, 2023, the minimum is 14.3 SEER2 under 45,000 BTU an hour of capacity and 13.8 SEER2 at or above it; split-system heat pumps must meet 14.3 SEER2 and 7.5 HSPF2. Compliance runs on the installation date, and a contractor may not legally install a unit below the standard.

Do HVAC companies in San Antonio charge more for emergency or after-hours calls?

Usually, yes — the reason is labour bought at unsocial hours, not the repair itself. What we cannot give you is a figure: no official source publishes a San Antonio call-out fee or after-hours premium, and TDLR does not regulate prices. Ask the trip charge before you book the visit.

Areas served in and around San Antonio

Tell us your neighbourhood when you request a quote, and we will match you with a professional who covers your part of the city.

The list, once verified, describes the San Antonio area this page covers for matching a homeowner with a professional — a coverage area for this page, not a claim about any one company's service area.

Related services and other Texas cities

Disclaimer. The costs on this page are estimates only, computed from the sources below with their assumptions printed next to them. Your final price depends on your home, the job and the scope you agree, and costs vary by job, material and location. Always confirm a contractor's licence and insurance before work starts.

Sources

  • Texas Department of Licensing and Regulation — ACR contractor licensing: classes, endorsements, insurance minimums, License Search and final-orders search (tdlr.texas.gov)
  • City of San Antonio, FY 2027 Development Fee Schedule (revised October 2026) — Heating and Air Conditioning (Mechanical) Inspection Fees for existing residential work: base fee, per-device items, surcharges, state-licence registration (docsonline.sanantonio.gov)
  • U.S. Department of Energy — 2023 central air conditioner standards FAQ: Southeast region SEER2 minimums (energy.gov)
  • U.S. Environmental Protection Agency — Section 608 refrigerant sales restriction (epa.gov)
  • U.S. Bureau of Labor Statistics, OEWS May 2025 — heating, air conditioning and refrigeration mechanic wages, San Antonio-New Braunfels metro and Texas (bls.gov; cross-checked via the U.S. Department of Labor's O*NET republication)
  • Home Outlet Direct — Goodman 3-ton split system package GLXS4MA3610 / CHPTA3630C3 / GRVT800804CN, retail price seen November 17, 2026
  • HVAC & Tools Direct — AmRad USA2236 dual run capacitor, retail price seen November 17, 2026
Call for a free quote Get a Quote