Metal Roof Cost in Texas: Per Square Foot, by Metal and Profile

Metal roof cost in Texas is not one number, and the national averages will not give you one either — they disagree by tens of thousands of dollars. This guide explains why those averages are measuring different roofs, breaks the price down by metal and by profile, and builds a real Texas example from named product prices and published wage data.

How much does a metal roof cost in Texas?

A metal roof on a 2,000 sq ft Texas roof runs about $10,000 to $32,000 installed across all profiles, at $5 to $16 per square foot (HomeGuide's figures). Corrugated steel sits at the low end, standing seam in the middle, copper at the top. Our Houston build-up for an exposed-fastener steel roof on that size came to $9,100 to $10,600.

Those are HomeGuide's national installed figures applied to a 2,000 sq ft roof. Texas labour usually runs below the national picture — Angi puts its Texas average project at $10,700 against a national average of $11,769 — which is why our computed Houston example, further down, lands at the lower end. Where your roof falls inside the range depends mostly on two choices: the metal, and the profile (how the panels are shaped and fastened).

ProfileInstalled cost per sq ft (HomeGuide)On a 2,000 sq ft roof
Corrugated / exposed-fastener panels$5–$12$10,000–$24,000
Metal shingles$6–$14$12,000–$28,000
Stone-coated steel$7–$13$14,000–$26,000
Standing seam$9–$16$18,000–$32,000

Why do metal roof prices vary so much?

Start with the three headline averages you will meet everywhere:

None of these is a misprint. They are averages of different things. Angi's figure is the mean of real projects its network actually sold, and that mix is heavy with smaller, simpler jobs — a corrugated roof on a modest home pulls the average down hard. HomeGuide's average describes the typical full replacement it sees, standing seam included. This Old House is not averaging sold jobs at all: it applies Homewyse's estimating model — builder-grade materials, medium-tier labour rates, standard-shaped roofs — to a 2,000 sq ft home, and a model that prices every roof as a full-spec replacement lands far above a sales average.

So "average metal roof cost" mixes profiles that differ by a factor of three, and sold prices with modelled prices. The only version that means anything for your house is a per-square-foot rate for the profile you actually want, multiplied by your roof's measured area — plus tear-off, underlayment and permit, which some averages bury and some leave out.

Cost by metal: steel, aluminium, zinc, copper

Angi's by-metal table (installed, per sq ft) shows how much of the spread is the metal itself:

MetalInstalled cost per sq ft (Angi)Notes
Aluminium$4–$11Light, will not rust; a common coastal choice
Steel$6–$16The default for Texas homes — galvanized or Galvalume-coated
Zinc$6–$12Self-healing surface; a premium, less common residential choice
Copper$15–$30The top of the market; priced for appearance and longevity

Steel dominates Texas residential work, and within steel the coating matters: Galvalume (an aluminium-zinc coating) is the standard panel finish sold for homes here, and it is what our worked example prices. If a quote for a steel roof lands in copper territory, that is a question to ask.

Cost by profile: corrugated, standing seam, shingles, stone-coated steel

The profile decides how the roof is fastened, and fastening is where the labour goes.

Corrugated and ribbed panels (exposed fastener) are screwed through the panel face into the deck, each screw sealed with a neoprene washer. They are the cheapest metal roof to buy and the fastest to install — HomeGuide puts them at $5–$12 per sq ft installed. The trade-off is maintenance: thousands of washers age in the Texas sun, and the roof needs periodic fastener checks.

Standing seam panels lock together over concealed clips, so no fastener is exposed to the weather. It is the profile most cost guides picture when they say "metal roof," at $9–$16 per sq ft installed (HomeGuide). Its panels are usually formed for the specific roof rather than bought off a shelf, so its price here comes from contractor data, not a retail build-up like the one below.

Metal shingles are smaller interlocking pieces stamped to look like shingle, shake or slate — $6–$14 per sq ft installed (HomeGuide) — for homes that need a conventional look. Stone-coated steel is a steel panel surfaced with stone granules, $7–$13 per sq ft installed (HomeGuide), often chosen in hail country and where a bare metal look is not welcome.

Worked example: a 2,000 sq ft Texas roof, priced two ways

Here is the build-up we can defend line by line. The stated job: a Houston home with 2,000 sq ft of roof surface (20 squares), a simple gable, one existing shingle layer to tear off, a sound deck, replaced with painted Galvalume exposed-fastener panels. Materials are priced from named products at The Home Depot, read on 19 November 2026. Labour is a declared assumption — 3.0 to 4.0 crew-hours per square for tear-off and installation — charged at a billable rate of three times the BLS OEWS mean roofer wage, the same labelled assumption our other cost guides use. Wages are not prices; the multiplier turns a wage into a crew rate, and we show it rather than hide it.

Materials

ItemBasisCost
Panels: Gibraltar SM-Rib 12 ft, 29-gauge painted Galvalume (model 987666)$64.49 per panel, 36 sq ft coverage; 62 panels for 2,000 sq ft + 10% cutting allowance$3,998.38
Underlayment: GAF FeltBuster synthetic (model 0973)$119.00 per roll, 1,000 sq ft coverage; 2 rolls$238.00
Screws: Gibraltar #10 × 1½ in galvanized, neoprene-gasket (model 06709)$29.70 per 250-bag; assumed 80 screws per square = 1,600, so 7 bags$207.90
Ridge cap: Gibraltar RC2 in Tan, 10 ft (model 987671)$39.04 each; 40 ft ridge assumed, 5 pieces allowing laps$195.20
Materials subtotal$4,639.48

Labour, disposal, permit

ItemMethod 1 — Houston wageMethod 2 — Texas wage
Billable rate (BLS OEWS mean roofer wage × 3.0, assumption)$22.18/hr → $66.54/hr$22.69/hr → $68.07/hr
Labour, 60–80 crew-hours$3,992.40–$5,323.20$4,084.20–$5,445.60
Landfill tipping for the old shingles$149.18$149.18
Houston re-roof permit$353.15$353.15
Total$9,134.21–$10,465.01$9,226.01–$10,587.41

The tipping line is disposal only: 20 squares of shingles at a minimum of 235 lb per square is 2.35 tons, at the U.S. average landfill tipping fee of $63.48 per ton (EREF 2025). The permit is Houston's published re-roof schedule for a 2,000 sq ft home — $255.67 fee + $63.92 plan review + $33.56 administration — as itemised in our roof replacement cost guide.

Published range: $9,100–$10,600 for the job — about $455–$530 per square, or $4.57–$5.29 per sq ft. Two honest warnings. First, it sits at the bottom of HomeGuide's $5–$12 corrugated band because it is priced at retail material cost and Texas wages, and because of what it leaves out: eave and gable trim, flashing, closure strips and sealant, decking repairs, and dumpster rental are excluded — we could not ground shelf prices for all of them, so we named them instead of inventing them. A real quote includes them, which is part of why real quotes land higher. Second, it is a documented-cost build-up, not a survey of quotes. Use it to judge a quote's shape, not as a quote.

Metal vs asphalt shingles in Texas

Our Texas roof replacement cost guide prices an architectural-shingle replacement in Houston at $345–$415 per square. Scaled to the same 20 squares, that is $6,900–$8,300 — against $9,100–$10,600 for the exposed-fastener metal build-up above, and $18,000–$32,000 for standing seam at HomeGuide's rates. Metal costs more on the day. The comparison flips when you divide by service life: HomeGuide puts asphalt at 15–30 years and metal at 30–80+ years.

Asphalt shingles (20 squares)Exposed-fastener metal (20 squares)
Installed total$6,900–$8,300$9,100–$10,600
Expected life15–30 years30–50 years (corrugated, humid climate)
Cost per year of life$230–$553$182–$353

We priced the asphalt side of this metal vs asphalt comparison in our Texas roof replacement cost guide, which shows its own build-up the same way.

Two Texas-specific points sit on top of the arithmetic. Hail: the panel in our example carries a Class 4 impact rating — the highest class — built to take hail that cracks and bruises shingles; hail can still dent metal cosmetically, which is a different problem from a leaking roof. Heat: the U.S. Department of Energy's cool-roof guidance notes that a reflective roof surface can stay more than 50°F cooler than a conventional one under the same sun, and that factory-painted metal is a standard cool-roof option — in a Texas summer, roof surface temperature is not a detail. And on the coast: in the TWIA catastrophe area (the 14 first-tier coastal counties and parts of Harris County east of Highway 146), a replacement roof needs a windstorm Certificate of Compliance to keep the home eligible for TWIA cover, metal included.

What pushes the price up or down?

How to get a comparable quote

Quotes only become comparable when they itemise the same things. Ask every roofer for the same breakdown, in writing:

  1. Panel specification — manufacturer, profile, gauge, coating (Galvalume or galvanized), and finish warranty. The SM-Rib panel above carries a 40-year finish warranty; your quote should name its equivalent.
  2. Underlayment — type and brand, and whether a high-temperature product is used.
  3. Fasteners — screw type and neoprene washers on exposed-fastener roofs; the clip system on standing seam.
  4. Tear-off and disposal — how many layers, and whether tipping/hauling is included or billed later.
  5. Trim, flashing and ridge — itemised, not folded into a single "materials" line. (Our build-up had to exclude these; on a quote, they should be present and priced.)
  6. Permit — who pulls it, and the fee as its own line.
  7. Credentials you can check. Roofing has no Texas state licence — anyone who claims one is telling you something false. What you can check instead: a voluntary RCAT licence (the Roofing Contractors Association of Texas runs a public search), manufacturer certifications such as GAF's or Owens Corning's contractor tiers, and the insurance certificate — the Texas Department of Insurance advises calling the insurer named on it to confirm the cover is real.

With two or three quotes in that shape, the differences stop being salesmanship and start being specifications. Compare them against the build-up above, then compare roofers in your city when you are ready to request a quote.

Frequently asked questions

How much does a metal roof cost per square foot?

Installed, $5–$16 per sq ft across all profiles in HomeGuide's national figures: corrugated at $5–$12, metal shingles at $6–$14, standing seam at $9–$16. Our computed Houston build-up for an exposed-fastener steel roof came to $4.57–$5.29 per sq ft before the trim, flashing and disposal lines it excludes — which is why it sits just under that band.

Is a metal roof worth it in Texas?

On cost per year of service, often yes: $182–$353 a year for the exposed-fastener example above against $230–$553 for asphalt on the same roof, before counting hail resistance and heat reflection. It is worth the least to someone who expects to sell soon — the premium is paid up front and recovered over decades.

How long does a metal roof last?

HomeGuide puts metal roofing at 30–80+ years depending on metal and profile, with corrugated at 30–50 years in humid climates and standing seam at the longer end; zinc is listed at 80–100 years. The finish on the panel in our worked example carries a 40-year warranty. Fasteners and sealant on exposed-fastener roofs need attention long before the panels wear out.

Does a metal roof cost more than shingles?

Yes, up front — roughly $9,100–$10,600 against $6,900–$8,300 for architectural shingles on the same 20-square Houston roof in our build-ups, and standing seam runs well beyond both. The honest comparison is cost per year of life, in the table above.

Will insurance pay for a metal roof after hail?

Your policy decides, and the deductible does the first piece of maths. Many Texas policies carry a percentage wind/hail deductible: the Texas Department of Insurance's own example is a home insured for $150,000 with a 5% deductible — $7,500 owed by the homeowner, so a $6,500 roof repair pays $0. Check two things in your wording before you file: whether the deductible is a percentage, and whether cosmetic dents to metal are excluded — a dented-but-sound panel is treated differently from a punctured one. And one Texas rule protects you in every case: a contractor who offers to waive or absorb your deductible is breaking the law (Business & Commerce Code §27.02(c)), and the Texas Department of Insurance says so plainly.

How we priced this: every figure above is either quoted from the named source next to it (Angi, HomeGuide, This Old House, the U.S. Department of Energy, the Texas Department of Insurance, BLS wage data) or computed from the named inputs shown in the worked example. Labour uses a declared assumption — three times the BLS OEWS mean roofer wage — because wages are published and crew rates are not; the assumption is printed wherever the rate is used. Figures we could not ground this way (trim and flashing packages, decking replacement, dumpster rental) are excluded and named, not estimated.

Disclaimer: ServicesInn is an independent Texas home-services guide. We research what local jobs cost and publish the sources behind our numbers; we do not do the work ourselves. Costs here are planning figures built from the sources shown, not quotes — your roof's measured area, pitch and condition set your price. Roofing is not a state-licensed trade in Texas; there is no Texas roofing licence to check, so verify the credentials listed in the quote section instead.